ucp 220 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = .8 height = 15 mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: inner_diameter = 55 pattern =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: pattern_copies = 20 inner_diameter = 55 pattern_rotation = 180 height = 10 pattern_size = 10 pattern =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 67 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 30 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=279864 Instructions Using the following options: trunk_length = 40 branch_diameter_cutoff = 1.6 tip_max_ratio = 70 root_min_ratio = 50 max_number_of_branches_from_each_branch = 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

I used 3V power (two AAA batteries) and two 220 Ohm resistors. You may adjust the circuit to your power selection. Battery holder I improvised a battery holder from things I found home. This includes a prototyping board, metal contacts from an old...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 mirror = Yes shape =...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

The list of parts you will need is as follows:An Arduino-based microcontroller (Arduino Pro Micro in my case)A real-time clock module (DS3231 or similar)A TowerPro MG995 continuous rotation servo motorA standard LEDA standard light-dependent resistor...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

for PLA+ (.3mf and .gcode are in 0.15mm with the .3mf being optimized for Prusa MK3s+ Printers that are well calibrated or factory calibrated)  Hot-End Temp: 220-225 for first layer smush and good adhesion if not using brim (not suggested since...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: height = 15 shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

That would recover a bed Y-dimension back to 220. So, after all the print area will be 210x220mm... Parts to print: all parts at last 50% infill, Gyroid or Quarter Qubic, PLA or PETG except two parts close to HotEnd, for them ABS is the must all...

(see the print settings). For the LED-s I used 220 ohm resistors between the RPI GPIO pins and the LEDs. For the Reset button, you need to connect it to the RUN pins, that are located on the board. You need to solder some connector pins on it if you...

http://www.thingiverse.com/apps/customizer/run?thing_id=243650 Instructions Using the following options: box_shape = 0 box_top_height = 10 box_height = 20 custom_shape =...

The scale of this model made in proportion to it. 1/8 for FDM version and 1/16 for SLS/SLA version.FDM version dimensions:After being printed will stand - 220 mm tall, 94 mm wide, 99 mm deep;SLS/DLP/​SLA version dimensions:After being printed will...

http://www.thingiverse.com/apps/customizer/run?thing_id=243650 Instructions Using the following options: build_plate_selector = 0 custom_shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...