ubs logo 3d models

(After repairs of course)Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

 - BNO08x: This means the part is meant for BNO08x or MPU 9250/6500 chips- 503759: This means the part is meant for batteries that are 5x37x59mm (based on that batteries sizing).- SS22F32: This indicates the part was designed for the switches...

Worlds are waiting.Equip yourself today, citizen!Space Port - https://www.printables.com/model/205432-space-port-terrain Starship Cargo Pod - https://www.printables.com/model/224797-starship-cargo-pod Starship Transfer Tug -...

(Support Enforcers Only)Print 2 of the “Space-Port-Addon-Bridge-MOD-Wrecked-Support,” one of everything else.Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Modules does not lift off (long...

When engaged in a full frontal attack, they are quite literally, unstoppable.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

Instead of painting the Dyna-Soar shield logo I now plan to print it out on high gloss photo paper, seal it, and then glue it over the raised shield. I think that will look much better.</p> <p>Hope to get some more done soon and update the post!</p>...

I also upload the firmware binary file (firmware.hex - ITALIAN LANGUAGE!) as well as the _Bootscreen.h file in which, to make the difference with the original firmware more visible, I made the same initial logo but in negative. CONFIGURATION...

I use it on a plywood deck where my synthesizers are crowding along with my science fiction models. A support enforcer is neededNo gluingEasy to printDesigned on...

(Support Enforcers Only)Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Mods do not lift off (long build). Other parts to use with the Space Port Center Bridge Module:The original Space Port -...

My filament guide does not have tubes in as I drilled out the holes a little but this is up to you. Included with the filament guide and Hot End camp STL parts you can use the optional dual colour logo's or use the NO_LOGO versions. I am using the...

Make sure you select the right colours for the inlays - the original logo should be around on your desktop somewhere.Assign each object a different extruder by right clicking on the "default" Extruder in the object list.Slice the model and transfer...

Violence is never more than a heartbeat away.Use those guns! Deliver your cargo!Stay in the fight!Small painted-on supports are required for Gun overhang (Support Enforcers Only.)Can be printed without support (I did it as a test.)Resize for smaller...

Get you Platform Walkways today and sleep safely knowing that heavily armed patrols will keep the alien mutant scum from crawling into your hab, slitting your throat, and taking what's yours!Shelter yourself! Deliver your cargo!Stay in the...

This is an easy-to-print Synthesizer Stand for LYRA-8 Organismic SynthesizerWill support the LYRA-8 Organismic Synthesizer or Synthesizers around 266.7MM X 266.7MM or 10.5 inches x 10.5 inchesPlaces the Synth on a comfortable 5 degree slopeNo support...

correct measurements, centred with hot-end *ABL sensor mount also centred, ie Y offset = 0 *Minor improvements to Mount body Update 2 *Optimised wings to not need as many supports (needs new body) *Created new body with better mounting to x-carriage...

----------------------------------------------------------------------------------------------------------------------- OTHER REMARKS: I designed the layout myslef: - The logo is based on figures on some other RFID products but unique. - The QR...

(Support Enforcers Only)Super glue works best.Resize for smaller or larger use.Clean your build plate with dish soap to ensure the floor of the Modules do not lift off (long build). Other parts to use with the Space Port Power Station:The original...

- *Slime*: This part has the SlimeVR logo on it, mostly for the lid. - *Blank*: This part has no print or logo on it, mostly for the lid. ### So which parts do i need? Of course this is totally dependent on the battery and switch you chose,...

Place your ducts with 2x M3 bolts.You can adjust the height of the ducts later.Then place 2 x 5015 cooling fans with M3 nuts and bolts as shown above.Fix 40mm fan and Cover-With-Logo with 4x M3 bolt to the main body.-Place snap on Duct-Left and...

Now you can print them out and use them for your nefarious purposes as you travel the far and vast star systems.The Original Galindos - https://www.printables.com/model/143724-galindos-robot-model-science-fiction Galindos Evolved -...

Instead of painting the Dyna-Soar shield logo I now plan to print it out on high gloss photo paper, seal it, and then glue it over the raised shield. I think that will look much better. Hope to get some more done soon and update the post! ...

Be generous, you can always shorten it later.Pick one direction to be up, I used the side with the printed logo. For each switch, mark it with the direction it triggers. This is reversed though. So if you push the stick up, the switch facing you is...

(Cards are laminated card stock)clip_Skills-Scores: Skill Scores backing piece slots into this angled clip.clip_Spells-Scores: Spell Score backing piece slots into this angled clip.Backings:backing_Ability-Scores: Angled backing that slots into the...

... is &nbsp;how the base module should look assembled. The logo billboard attaches and aligns with the light green key above the ramp.

The screen protector sleeve and the flexible Velcro straps are the only sewed parts. I printed all the parts out of PETG at 0.3mm layer heights.  No supports for any of the parts! I have included a short build guide in the downloads with more...

I printed the case with 3 perimeters, but two should also work.You don't need any supports for the print.(MK3) There are four different traverses, three different logos and one without. Also two variations of the knob for the LCD cover, you can of...

Tl;DR 0 – Prerequisite 1: You Need to Have Done Extra Mosfet on the Board First Please see https://www.thingiverse.com/thing:1035348 0 – Prerequisite 2: The Rear Mounted Fans Need 3.0mm More Clearance So You Will Need to Glue On a 3mm Spacer for the...

Then I thought: what better way of showing our loyalty to Prusa than having a giant Prusa Research logo on the wall? And let's make it functional! So, the Floating Prusa Research Shelf was born! :)Anyway, down to business. The Floating Prusa Research...

Before installing the thermocouple and the heat cartridge determine which will be the right and left side hot end.  The heat blocks will be installed with the Slice engineering logo facing on the outward sides of the extruder.  This is to...

A rating or tip is also welcome and may check out my other designs!&nbsp;Happy printing!&nbsp;&nbsp;Print instructionsAll parts are optimized for FDM printing.Please use a 0.4mm nozzle (or smaller).I advise to use the .3mf (or gcode) files, as all...