ubitx enclosure 3d models

To learn about this setup, checkout the 2 YouTube videos linked in my V1 and V2 printer enclosure designs, linked below:V1:https://www.thingiverse.com/thing:5137500V2:https://www.thingiverse.com/thing:5166976Print SettingsPrinter:BIQU...

1.2Runtime counter placed to keep track of the working hours/on-time of the Laser. The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20This box will fit in the enclosures made by Stepcraft.Hardware:DS...

This is a continuation of my previous replacement lid; https://www.thingiverse.com/thing:4761348 Description This is a three-part lid for the Ender 5 and Ender 5 Pro (as I have been told) electronics enclosure. My goal was to create a perfectly...

Everything here on this design still works sufficiently to extract your fumes, but the additional option uses the desktop fume extractor with a larger blower fan and will move more air from the enclosure if you prefer. See x2 photos I have added...

The file is parametric, so you can try making it even shorter if you want...........................This piece is threaded for PC4-M10 quick-fittings for 4mm PTFE tubing (same stuff the prusa mk3s and most other printers use)Here are a couple links...

I do use an enclosure, but poor adhesion will mess with any abs print. And besides, I stuck this on at 3am and decided it was bed time.Thanks to the original designer for his great stl that made this much easier to get done. This is still a work in...

This is a small add-on for my IKEA Ender 3 enclosure. I wanted to store my tools convenient enough that they're not always lying around but also are pretty close, that I can get them in seconds. So I designed a very simple magnet holder. It's a...

They also print support-free :)I personally use 4x 5mm Deep Feet and 1x 5mm Z Axis Foot ( What the pre-sliced gcode contains and all I have tested ), however, I have to use small paper spacers to stop the printer from rocking as the table my printer...

It is basically a new enclosure for a cheap 3" plasma ball lamp. Some soldering is required. Building this requires: A 3" plasma lamp A small phillips screwdriver, 5 M3 screws and the hex wrench to drive them. A panel mount toggle switch (4.5mm...

A dedicated enclosure for your Impos.... I... I mean PC, to keep protected from dust and the occasional kick when you are playing spin the chair. The Table top has dedicated slots for fixing your office necessities so that they are easily accessible....

Apply a number of layers of clear nail varnish to fully seal the enclosure, particularly in the central hole where the shaft will pass through. This updated design requires the QuadLock top black part to be modified so that it is 18mm the...

The emergency stop gets mounted on the outside of your enclosure box and routed back to the GRBL pins. Now you are ready to assemble the laser! The laser goes into the laser heat sink, which goes in the cooling duct. The duct blast shield gets...

Second, the opening is too small for the fan to force air through, which creates back pressure in the enclosure that you can feel coming out of the back of the fan, All that air flow gets wasted instead of being used to actually cool the part. ...

Update 2/25/2018 I've installed an enclosure, but I'm still working on cutting the press board for the "laser-proof window" with an OD of 3. I created four L/U channels that were solvent-welded to the corner pieces, allowing me to easily slide in...

https://www.thingiverse.com/thing:4686693Features:manual set the Laser power or use PWM control, check laser temp and off parallel in-out on DS 15 connectors (in from CNC controlboard, out to aux)Input to use only PWM signal from DS15 pins 2...

My printer tried to impress me and the entire fan-sides of the shell (the two side-enclosures where you would put the fan and that would be high on the build plate) were printed without supports in the middle. Even with the best printer, doing 15cm...

Limitations of the Pint Form Factor: Small Enclosures (cant fit a 15s battery with a standard size BMS inside). Small Tire (Pints have a 10.5 inch diameter tire, lets make that 13 inch) Lack of Customization (With Future Motion's presigned frame,...

This Y-axis linear rail mod uses 9 mm rails with MGN9H: the carets there are only 20 mm wide, which makes installing an enclosure easier. There is very little disassembly, so you can install it quick and easy. You will not even have to disassemble...

Just make sure they are suitable for dish washer use, so they can handle the temperature. *4 self cutting screws (the two delivered with the device are fine, but the case is prepared for four screws and you need slightly longer ones to secure the...

PLA can work if you only ever print PLA, but if you plan on occasionally printing PETG, ABS or other higher temp filaments or if you use an enclosure in summer, you will need a higher temp resistant filament or it will deform and collapse. List of...

I removed the hole in the back and made the enclosure deeper. Since the Raspberry Pi on the RatRig is located remotely, it won't be mounted on the back of the screen as is typical.</p><h4>Hardware Required:</h4><p>1 x Raspberry Pi 7" Touch Screen...

The standard NEMA Type 3R enclosure makes the unit suitable for both indoor and outdoor applications and is designed to be floor mounted. Wall mount brackets or additional mounting accessories can be purchased separately. This 30 KVA distribution...

The unit features an above deck mount for the radio, Control panel with gauges for all of the electrical (Battery/Charge/Source etc.) This was built using: Apache 3800 case from Harbor Freight TH-9800 radio (I got it through Amazon, but you can get...

The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20 This box will fit in the enclosures made by Stepcraft. Hardware: DS 15 connector female (signal out) DS 15 connector male (signal in) Mono...

Though it's possible to set it up on the other side of the gantry, I put mine on the near side so the spool is closer to the opening of my enclosure to make changing it even easier. Yes, since the angle of the holder is lower than the original one it...

6x #4x12mm screws (for Nano enclosure and control box lid). 2x 3mm bolts, ~ 15-20mm long (for motor). 1x M6 bolt (for camera mount) 1x M6 threaded rod. In terms of weight capability, the main factor is probably the acrylic panels and plastic rather...

This is a modular Single Board Computers enclosure for up to 4 devices. The device cards are held vertically. This design let you service one card without having to remove the cards on top of it like in the previous design ...

Klipper), dual-motor Z-axis upgrade, silicone pads replacing the bed leveling springs, an enclosure, plus a red racing stripe and a highly-aerodynamic spoiler at the rear to make it go super fastNozzle:0.6mm brassMaterial: eSun PLA+ in my favorite...

The noise when I mounted the psu under my lack enclosure was close to a hair dryer. There are several ways to reduce the noise coming from the LRS-350, such as replacing the 12v 60x15mm fan with something more quiet. You could also cut/drill the top...

Test subjects break out of their cryo chambers and enclosures, too strong to be contained any longer. This happens simultaneously as if acting on some unseen signal. They attack the lab workers and anyone scratched becomes infected too. The...