tx16s gimbal protector 3d models

Radiomaster TX16s gimbal protector for Sticky360.

... is well protected against scratches and bumps. Available in various styles to suit different user preferences, these gimbal protectors are an essential accessory for anyone who wants to extend the lifespan of their Radiomaster TX16S device.

The Tx16s gimbals have a little nub on the bottom that gets in the way of most protectors so I cut it out a bit. Made a bit taller to fully cover the gimbal and protect the inside of my case/bag. Bored the gimbal hole out a bit to fit properly. I...

I really liked the TX16s Gimbal protector by RobinStoraa ( https://www.thingiverse.com/thing:4538922 ) , but those kept falling off, so i designed a simple lock to insert in the holes present in the gimbal protector. Those use a slotted hole to grip...

Some Key Features I found important: - Both Gimbal Protectors connected in the middle, no singles - Connector should allow for Stock Gimbal Position aswell as Lowered by up to 3mm - Sticks shouldnt be sticking out of the top - No weird aesthetics,...

I didn't like any of the available Designs for Gimbal Protectors already uploaded on Thingiverse so I decided to design my own improved version. Some Key Features I found important: Both Gimbal Protectors connected in the middle, no singles...

Inspired by https://www.thingiverse.com/thing:4751111 with the following improvements: - Dust protection - Better fit (not sure if you have a skinned radio) - Less support needed (need some at least of the pins) Can be printed with low...

This Radiomaster TX16S gimbal protector fits MAX version and AG01 gimbals. ...Plus, still no cringe graphics and other lame details

While I liked a lot of the gimbal protectors out there, I really wanted a single simple piece that would grip the control stick and not fall out. I printed these out of a flexible filament, but they may work as a snap fit PLA. To put them on I just...

a double gimbal protector for a Radiomaster TX16s MAX (large center hook) for 14mm lotus sticks and one for 10mm sticks. since no protector was working for me or they had terrible graphics, i made my own. They have a small notch to keep them on...

I remixed this Gimabl protector for TX16S in order to have a better grip when removing the protector (can be done one hand without scratching anything). Also, to be able to have a view on the charging indicator while the protection is on. Print...

I remixed this to 1) shorten the height by 5cm and 2) cut off half of the clip that connects to the mounting piece on the TX so that it fits with a lanyard attached to it.

Gimbal and switch protector was designed for transmitter EACHINE TX16S, but should be usable also for standard Radiomaster TX16S. ... Note 11/11/2021: Replaced wrong STL with correct one

Resized to accommodate AG01 gimbal stick ends.

A remix of roobidesign's excellent Rotor Riot Gimbal protector for the Radiomaster TX16S. ... Printer either standalone protectors for each gimbal or the version with the brace for added convenience (brace needs support, standalone protectors print...

After a couple revs, this is what I came up with for the RadioMaster TX16S with the regular Hall effects gimbals and regular stick ends. In case you want to tweak it a bit more, below are the variables I used. ... gimbal_face_diameter = 49.5;...

The protectors were modified to use M3 screws everywhere, other then that: - Bottom part - designed to be printed in Flex filament, thicker arm walls, screw holes are 2mm wide to snugly hold 3M screws. - Holder - size adjusted for thick tx16s stick...

Printed with PLA

This gimbal stick protector is for 10mm stick-ends on a TX16S MAX radio (or a TX16S radio with gimbal rings). If you want the engraved text to have a different texture from the rest of the bar, print it upside down (with the text touching the build...

Gimbal Protector for the Radiomaster TX16S I have larger [Gimbal Stick-Ends](https://www.thingiverse.com/thing:5139591) than the stock stick-ends. I wanted a Gimbal Protector that would fit over those but also fit in the Radiomaster TX16S case (the...

Gimbal Protector for the Radiomaster TX16S I have larger Gimbal Stick-Ends than the stock stick-ends. I wanted a Gimbal Protector that would fit over those but also fit in the Radiomaster TX16S case (the one that comes with the transmitter). There...

This is a remix from https://www.thingiverse.com/thing:3794980 A simple and easy to print gimbals and switches protector for your tx16s in case you are using stick ends with a diameter < 14mm. I use it with m4 lotus stick ends. ... If you have...

This is a remix of https://www.thingiverse.com/thing:4497596 I redesigned these parts to work with gimbal spacers like https://www.thingiverse.com/thing:4460901 The center part from the original design has to be used.

AG01 gimbals protector for Radiomaster TX16S

... the remix of that gimbal stick protector ( https://www.thingiverse.com/thing:4743736/). ... Seem that the TX16s MAX mk2 with new CNC gimbals got some difference on sticks distance measure, so i modified the linkage bar to 102 mm (center hole spacing).

This is a thing to protect your RC transmitter gimbals (sticks) when you carry it in a backpack. It will fit Radiomaster TX16s. It might also fit Jumper radios, but it wasn't tested yet.(pls let me know if you can test it. thx!) The original is...

Just print it!

Compatible with Radiomaster TX16s, Jumper T16/T18 Print em and install em or ur gimbal go boom boom with $60 replacements