twotrees bluer plus 3d models
53218 3d models found related to twotrees bluer plus.thingiverse
Modification to the printer TT Bluer Plus. The motor is mounted above the aluminum profile. Motor model: 0.9 NEMA17 slim power LD0-42STH25-1404MAC. I changed the motor steps to 820 (steps/mm) in cfg file. ...I used the original screws.
thingiverse
##You'll need: 4 m3x15mm screws for the top piece 4 m3x6mm for the wire harness adapter (4 Threaded brass 5mm inserts if you want to use the mount made for that) ##Assembly: You can leave the Hot end attached to the printer. 1. Remove...
prusaprinters
Made this because my hot bed got caught on the wires and caused serious damage. Holes are for zip ties. Mount with m3x6mm screws. Mount holes are already there so no drilling! ... Category: 3D Printer Accessories
thingiverse
Made this because my hot bed got caught on the wires and caused serious damage. Holes are for zip ties. Mount with m3x6mm screws. ...Mount holes are already there so no drilling!
thingiverse
This is a adapter that allows you to attach a bowden tube to the runout sensor. ...You'll need to replace 2/3 screws of the runout sensor with longer m3x25mm screws, and replace the two screws that attach to the electronics housing with m3x8 Uses...
thingiverse
Made this so I could mount a wifi antenna outside the bottom enclosure for Octoprint. No drilling just take the bottom of the printer and the 4040 extruded aluminum under the Z-axis and feed the wire through the top to the base. You can mount on the...
thingiverse
Simple design Helps guide the filament away from electronics.Need to replace the screw with a m3x25mm one to attach it.
thingiverse
Easy conversion for your TwoTrees Bluer Plus to direct drive. Use the existing stepper and BMG feeder. All you need is a longer 4-pin to 6-pin stepper cable and (if you use it) a long 3-pin cable to connect the filament runout sensor Print...
thingiverse
New spool holder for TwoTrees Bluer for wide spool Just print and install Need one support - show on picture
thingiverse
This mount is suposed to use in a TwoTrees Bluer. All the distances are measured for this printer. Happy printing ;)
thingiverse
For "Two Trees Bluer" 3d printer. UPDATE :06/01/2021 add more firmware options (MKS fw and Marlin LVGL_UI) , and update marlin. Do not print on PLA, PLA deforms with heating of the hotend. After installing the probe you must configure the...
grabcad
This is a mount adapter for TwoTrees Bluer 3d printer using 3Dtouch probe.Leveling settings:Probe x axis offset: 41.5Probe y axis offset: 0Probe z axis offset: -3.2
thingiverse
This is a simple mount for the PL-05N / PL-08N sensor This mount is suposed to use in a TwoTrees Bluer. All the distances are measured for this printer. Happy printing ;) Telegram group: https://t.me/twotreesbluerbr (Bluer's owners group from...
thingiverse
This Mount for a E3D was made for the Zwo Trees Bluer. Feel free to use this. It was my first project. Not tested yet. ...
thingiverse
An adjustable Z endstop holder for the TeoTrees Bluer 3D printer. I hope it will be as useful to you as it is to me. ... You need one M4x ~50mm screw and two M4 nuts to assemble the movable part, as well as two small M4 screws and their hammer nut...
thingiverse
TwoTrees BlueR PTFE Tube & Cables Holder BOM: 2x M3x16 Screws Material: PLA
thingiverse
This is a profile for PrusaSlicer made for the Bluer 3d printer by TwoTrees. * Make sure you have closed PrusaSlicer before extracting the rar file. You'll have to extract the archive content in the PrusaSlice\resources\profiles folder. (it's...
thingiverse
Led light bar holder desiging for TwoTrees Buer, but will fit on any 20mm rail. For ABS printing maybe will require 0.5% to 1% adjustment for tight fit on rail. All parts can be printed separately. ... Enjoy.
prusaprinters
-PT-BREsse mod tem como objetivo trazer o Afterburner para a Bluer. O Afterburner "stock" é ideal para ABS porém deixa a desejar com PLA. Como a Bluer é muito usada para imprimir PLA, uma opção melhor seria utilizar um MOD chamado AB-BN que...
thingiverse
Using 1.5mm piano wire I got Ultimaker style on cable and tube. ... A cover for hiding cables in aluminium profiles. Will there be a Acrylic Kit for the Sapphire Plus? ... https://youtu.be/gZ7xSlnIvvI
thingiverse
bluer plus yazıcımda 3d touch arıza verince z endstop bağladım gerekli stl dosyasını yükledim. ... iki farklı yazılım oluşturduk arkadaşım ile kendı orjinal yazılımı ve marlin ikisinide yükledim
thingiverse
This is Roller type Filament Guide for Bluer Plus. Easy mounting just slot in pillar support for filament sensor. Required Bearing 608 which is very easily available. ... Spacer need to print 2 pieces.
cults3d
This is Roller type Filament Guide for Bluer Plus. Easy mounting just slot in pillar support for filament sensor. Required Bearing 608 which is very easily available. ... Spacer need to print 2 pieces.
thingiverse
TwoTrees BlueR V2, V3 X-Motor Front Cover RMX BOM: 2x M3x8 Screw
thingiverse
Bigger Levelling wheels for the TwoTrees Bluer 3d Printer. ... Just press fit them onto the existing wheels.
thingiverse
Gerekenler 2 adet 625zz rulman 2 adet 15mm m3 civata 4 adet m3 pul 2 adet m3 somun Required 625zz bearing x2 15mm M3 bolt x2 M3 washer x4 M3 nut x2
thingiverse
Gerekenler 50mm M4 civata x4 Required 50mm M4 bolt x4 Güç Kaynağına 120mm Fan Takabilmek için Gerekli Required to Install a 120mm Fan on the Power Supply https://www.thingiverse.com/thing:4943284