two person office 3d models

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

After all, the "PSU attachment" is fixed to the same frame as the other two screws, so I don't think it is necessary to use it, but I put it on just in case. If you are concerned about it, please remix the screws so that they are attached to a...

Two sharp attachments on the nose of the spacecraft and two vertical stabilizers in the back were installed to further aid the flight control. The top hull plated with ablative armour is riddled with authentic patterns, joined by the name of the ship...

Note there are two similar parts that could be the Lid knob bottom, you need the one with an hexagonal seat on the inside.Place the magnet and the spacer into the top of the Lid knob.Press a M5 nut into the Lid knob-bottom, temporarily using the M5...

Have much fun with it =)30.03.2023: Added two 4K videos to the description that show the complete setup process of the Arduino installation, code upload to the ESP32 board and the WiFi setup on Microsoft Windows 11 and Apple macOS. Hope this will...

The 3D printing Sparrow figurine has his long hair dreadlocked and customarily wears his goatee in two braids. The author of the model made sure to include Jack’s signature tricorne hat, bandanna, and lots of intricate beads and ancient coins that...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Insert said nuts into each slit photographed here. As you can see there are two slits per side, so that each screw may have a nut fastened to it. STEP 3Using your Hex key allen wrench set attach the  ¼" Tapping Inserts for Plastic to...

Both versions are to be identically assembled to the body of the bike;- The assembly of the front and rear shock-absorbers requires 2 regular ball pen springs and additional "pins" made out of short pieces of regular 1.75mm filament;- Rotation of the...

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

The windows on the driver compartment viewport are provided as two separate files to be printed with the transparent filament. The headlights and “parking lights” holes are made hollow for you to introduce LED wiring if willing. Moreover, the scale...

 It is working nicely through the gear train but the escapement gear is just a little tight against the gear_train gear so I modified the front and rear rails to push the escapement gear toward the balance section by about ⅔ of a mm to help keep the...

If you have a switch that toggles two connections at once (4 terminals), the ground wire can be toggled as well, but I think it might be better to keep the ground connected at all times.Make sure the toggle switch is rated for at least 5 amps (it...

The 3D artist made sure to carefully outfit the two-pilot cockpit and the two-storeyed cabin that is known to carry up to 40 troopers to their deployment site. Various hatches and lids all over the body of this destructive weapon conceal the...

I also created a design in two parts that allows an easy extraction of the box to dry the silical pearls while the base remains in place.You have more space than needed for the silica pearls so if you prefer, instead of pearls, you can buy sachets...

ABOUT THIS 3D MODEL“Batman has two primary modes of transportation: swinging from Gothic clock towers on his Batline, and cruising around Gotham in the Batmobile.”The sleek, long and low Batmobile featured in the 1989 Tim Burton’s Batman movie struck...

The "Anker-A" part has 2mm holes at the ends into which the other two parts are inserted. The "Anker-B" part is held by an M3 set screw and can be replaced if a writing stylus with a different profile is used. The "Anker-C" part is glued to the...

For those customers who have already purchased the Treebeard figurine or are planning to do so, every version of the Merry Brandybuck model comes in two variants to choose from - an independent static figurine (marked “Stand” in the “Source files”...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

In order to give all BttF enthusiasts an opportunity to make the iconic vehicle true to life, all model’s sets of wheels, as well as the spare wheel stored in the luggage compartment, come with two variants of the tyre to choose from: one is meant...

Briefly about the printer: it is a two-color printer with interchangeable print heads, which can work in filament color mixing mode and printing separately. Therefore, it comes with two detachable heads. Who cares - I previously published a <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a href="https://www.thingiverse.com/thing:3837220"...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a href="https://www.thingiverse.com/thing:3837220"...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a href="https://www.thingiverse.com/thing:3837220" title="Grinder....

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a href="https://www.thingiverse.com/thing:3837220"...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a href="https://www.thingiverse.com/thing:3837220"...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools &bull; Accessories <a...