two eyed mike 3d models

I added an Open hardware logo (courtesy of lamer https://www.thingiverse.com/thing:22445) design. No supports are required. This was uploaded to MyMiniFactory in 2021 and now I have moved it here as well.There are two different Fusion 360...

If you have a printer, then you have such electronics! PaScn3D connection to Prusa 3D printer in a minute (tested!) – dedicated mounting brackets, components adapted to the dimensions of the device Modularity – adaptation to other printers without...

To avoid this from happening, I highly suggest that you print them with 100% infill!To make the spool holder work, you need four 608 bearings for one set, which you can get from a local skate shop or from Amazon (by using the provided links, you can...

The two pieces are connected at the knee. The leg moving up and down causes the knee to bend. This is purely astetic. I'm sure the mechanism is nothing new. It also has swinging arms for a little added animation. There are pins on the top_leg parts...

The two violin waist pieces with the pipes required a bit of finagling with printing supports and cleaning. The bottom 2 parts of the neck had the coolest effect when printing flat, so I printed neck_part3 with supports (therefor the hidden under...

For my first two designs I used Freecad, but I got a bit annoyed by my designs getting corrupted and then having to start over again. For this design I used OpenSCAD and experienced no such issues, it “just worked”. I also learned a lot about gears...

I need two adjustable outputs, constant voltage/current, and voltages from 3.3 up to 30 V. Having 5A was one goal as well.</p> <p> <figure class="media"> <oembed url="https://www.youtube.com/watch?v=weG6X18faGc"></oembed> </figure> </p> <p>BE...

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a href="https://www.thingiverse.com/thing:3837220"...

I have made the car and "lane-changers" work in two different modes, one would be compatible with "mechanical" lane-changers like in Scalextric Digital System, WOS or Advance. The other mode would be the "InfraRed" mode, in which the "lane-changers"...

Two per strut are required at the front and rear. Alternatively, use springs 30mm x9mm x0.9mm, here only one spring is required per shock absorber. Update 23_12_2020 I uploaded the model "Zahnrad_18_23_neu", which I had forgotten. Thanks...

The two parts of the hair should meet in the middle sew them together glue all parts expect **M** and **N**. Fill the hair with stuffing and slowly sew them together. Lastly glue **R** part to the head cover. ### Electronics and Software Here...

I located it centrally around the existing tape, spool core and supports that I had previously modeled. Note: I kept the top and bottom meshes separate to make printing easier. Next I wanted to create a more positive connection between the head (top)...

You can find it as shown here:Then you'll have to paste the link in the website:Last thing to do is to download the code in the SVG format:Step 2Import the templateYou have to download the provided file called template.f3d here on thingiverse and...

(I just use the casing as a lens cap for storage and transport)In the US Amscope sells an objective which is identical in outward appearance (but I haven't tested it):https://amscope.com/products/pa4xk-v300I've included two adapter designs:The crop...

I have included a 1:1 floor plan to help position the supports but this is to be used as a guide only.I have also listed the wheels as optional as I ended up using two salvaged hoverboard tyres and built the rims around these dimensions but any type...

For the last two years I've been printing those (and similar) cases to sell on my little Etsy shop. In that time I've done five clean sheet of paper redesigns, each time incorporating improvements that I had learned from producing previous...

You can also print and use the optional "Roll-Off Savers", one on each side of the spool, to minimize the risk of filament jumping over the spool, although it's unlikely it will happen with this system, even with new spools.BOM1 x 608ZZ or 608RS...

The previous two kits covered United Earth Stellar Navy’s (UESN) ship designs [[part 1](https://drive.google.com/drive/folders/1BYPim7e8uL_T4dufwvlEwkRg8SV4jorT?usp=share_link)][[part...

Most of these changes were subsequently removed. ...

You can also print and use the optional "Roll-Off Savers", one on each side of the spool, to minimize the risk of filament jumping over the spool, although it's unlikely it will happen with this system, even with new spools.BOM - Bill of Materials1 x...

If you print them and something is wrong, please let me know and I will fix it. v1.11E3_Chassis_Manta_M5P_Bucks.stlThis model supports the BIGTREETECH Manta M5P. v1.12Added Chassis_Right_BTT_Relay_v1.2_BTT_UPS_dual_buck_@EricDrop_2040537.stlThis is a...

They should print as bridges quite easily.TIP: print two of the "Coupler" part, and use one to block the hole while refilling the machine, so that no food gets into the center hole.I would advise you to use black filament for the rotating part since...

These are only two colors, so there are fewer color changes (only 6). All the logo brackets print at once, so it's not that much extra work for the dramatic increase in flair! By the way, I scanned the Radio Flyer 90 logo for the rails directly from...

Assemble flipflop + flipflop-base + lock-TrayThe tray is a great way to finish the run and to store extra marbles. Print SettingsPrinter: Anet AM8Rafts: NoSupports: No, except for “The Wave” and “Lombard Street”Resolution: 0.2Infill: 20%Filament:...

Place two pieces of tape along/near the vertical sides of your laptop. This is where you will be placing the rails. Depending on the tablet/phone you use, you will need to change where exactly you place the rails, so do some measurements before...

Español: El objetivo de este vaso es permitir a las personas que tienen limitada la extensión de cuello beber sin necesidad de llevar a cabo este movimiento. En su parte superior tiene una abertura que evita que el borde choque con la nariz de la...

If your printer has poor bridging then I recommend using supports touching the build plate only.There are two versions of the board. One designed for a multi material, or dual nozzle printer, the other for a single nozzle printer with a filament...

I use only PLA or PETG.I have remixed a car body that fits the car: It's now available at  https://www.printables.com/model/298041-dodge-ram-rc-car-body-remix You will notice that this time I have nearly made a real bill of materials and the part...

After breakfast that morning, amid a group of very nervous apprentices, Wright calmly drew the plans in the two hours in which it took Kaufmann to drive to Taliesin. Wright designed the home above the waterfall, rather than below to afford a view of...

The groove and threaded inserts allow to fix additional tools like the drag-knife mount to the printhead.Cutting OperationsPrepare the drag-knife mountWhen needed, the drag-knife mount can be attached to the print-head with the two screws:Here, the...