two bladed scythe 3d models

Utility Protectron   5. Police Protectron- The visor on Regular Protectron and Protectron Medic head variants comes separately to be printed with transparent filament;- There are two extra variants of Protectron's body to assemble Utility Protectron...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

For those customers who have already purchased the Treebeard figurine or are planning to do so, every version of the Merry Brandybuck model comes in two variants to choose from - an independent static figurine (marked “Stand” in the “Source files”...

The teeth should still be approximately as they were on the print bed.The teeth should now be arranged into two double rows. The two left rows fit the upper gums, (to your left) and the right rows are for the lower gum (on the right).Now, add some...

 It is working nicely through the gear train but the escapement gear is just a little tight against the gear_train gear so I modified the front and rear rails to push the escapement gear toward the balance section by about ⅔ of a mm to help keep the...

The scene most likely takes place somewhere in the middle of the crime-ridden Gotham City so it is no surprise that the figurine is wielding two bulky guns, pointed at different directions. The 3D artist made sure to include all the trademark...

Insert said nuts into each slit photographed here. As you can see there are two slits per side, so that each screw may have a nut fastened to it. STEP 3Using your Hex key allen wrench set attach the  ¼" Tapping Inserts for Plastic to...

Basically, I've split the Selector carrier in two parts, which makes it easier to replace the endstop sensor on top or add some features like the servo variant or some laser detector, without the necessity of reprinting the whole carrier. You'd...

The 3D printing model's chosen scale is 1:700 for the FFF/FDM version and 1:1400 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 45 parts;- A printed ship is 152 mm tall, 318 mm wide, 680 mm deep;- Assembly...

In order to ensure the cleanest 3D printed result, Otachi’s tongue was extracted from the beast’s mouth, while the two parts of Kaiju's signature crest were cut off as well.All assembly parts are provided in STL files of FFF/FDM version in...

The two elaborately detailed donor cars stacked on top of each other rest on immense tractor tyres that elevate them above the ground and represent the militant Colonel's authority. So don't miss out on the opportunity to 3D print an addition to your...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

In order to give all BttF enthusiasts an opportunity to make the iconic vehicle true to life, all model’s sets of wheels, as well as the spare wheel stored in the luggage compartment, come with two variants of the tyre to choose from: one is meant...

The 3D printing model's chosen scale is 1:400 for the FFF/FDM version and 1:800 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 42 parts;- A printed ship is 133 mm tall, 480 mm wide, 469 mm deep;- Assembly...

The "Anker-A" part has 2mm holes at the ends into which the other two parts are inserted. The "Anker-B" part is held by an M3 set screw and can be replaced if a writing stylus with a different profile is used. The "Anker-C" part is glued to the...

Note there are two similar parts that could be the Lid knob bottom, you need the one with an hexagonal seat on the inside.Place the magnet and the spacer into the top of the Lid knob.Press a M5 nut into the Lid knob-bottom, temporarily using the M5...

For those customers who have already purchased the Treebeard figurine or are planning to do so, every version of the Pippin Took model comes in two variants to choose from - an independent static figurine (marked “Stand” in the “Source files” tab)...

The hexagonal holes must be aligned with the two spring pillars. 4th Update 20.12.2018 - Display stand & minor adjustmentsTired of leaning your fancy Revolver to a wall, a shelf, a mug or a candle because you don't want it to just lay around...

There were also prepared two different types of bearings for front and rear wheels of the 3D printing car. The reason why the front bearings are thinner is to allow for the simultaneous movement of front wheels with the help of a steering rack that...

The 3D printing model's chosen scale is 1:34 for the FFF/FDM version and 1:68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 2.0 version features:- Contains 30 parts;- A printed ship is 271 mm tall, 170 mm wide, 368 mm deep;- The updated...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

* Install the probe mount to the extruder plate using two short M3 screws. * Remove the 4020 duct, BMG and hotend, if installed. * Sandwich the extruder plate between the extruder stepper and the BMG, and start the three long M3 screws. Do not...

The model features the craft’s trademark three wings: a stationary dorsal stabiliser and two articulated flanking side wings. The 3D printing Lambda-class shuttle is heavily armed with a pair of forward-facing double blaster cannons, two wing-mounted...

After all, the "PSU attachment" is fixed to the same frame as the other two screws, so I don't think it is necessary to use it, but I put it on just in case. If you are concerned about it, please remix the screws so that they are attached to a...

The 3D printing model’s chosen scale is 1:350 for the FFF/FDM version and 1:700 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 50 parts;- A printed model is 152 mm tall, 416 mm wide, 312 mm deep;- There is...

The 3D printing model's chosen scale is 1/34 for the FFF/FDM version and 1/68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 62 parts;- A printed model is 191 mm tall, 397 mm wide, 719 mm deep;- Assembly...

The windows on the driver compartment viewport are provided as two separate files to be printed with the transparent filament. The headlights and “parking lights” holes are made hollow for you to introduce LED wiring if willing. Moreover, the scale...

Both versions are to be identically assembled to the body of the bike;- The assembly of the front and rear shock-absorbers requires 2 regular ball pen springs and additional "pins" made out of short pieces of regular 1.75mm filament;- Rotation of the...