tweeter pods for car 3d models

Rear ejection couplers for boost-glider pop-pods and other model rockets. They look like Y-couplers on the outside, but are U-vented on the inside. In handy-dandy BT-5, BT-20, and BT-50 sizes. I recommend printing these on their sides with a raft and...

This is a replacement for the tweeter support for hertz 165.3. In my infinite wisdom, I lost one while installing my, so I had to print one. ...

This text presents a straightforward CAD design for a speaker and tweeter, aiming to benefit others who may find it helpful.

it also leaves the inner angled section of the Speedhut Stealth black bezel visible, which I believe is more visually appealing than my original design that came all the way to the gauge face Each pod has 4x .1" holes modeled between the two halves...

A customized stand or mount for the Digital Designs VO-B3 speaker or other similar speakers that have a 43.5mm or 1.71 inch hole in them, ideal for mounting and holding your favorite tweeter securely in place!

I designed mounts specifically for aftermarket tweeters tailored to my 2007 Subaru Legacy. ... This project originated from the versatile Tinkercad platform, where you can edit and refine the design live at https://www.tinkercad.com/things/fAGWMInrdUG.

Holder for the awesome Pebble Audio 2:1 Speaker which are placed too low on my desk with the big Cintiq tablet. Lifts the Pebble tweeter about 10 cm in a matching design. ...

The tweeters of my B&W P6 are going bad (again) due to dried ferrofluid.I am not going to repair but replace them with two LAVOCE TN131.00 1.3in tweeters.Also i will not try to fit them in the original housing (the egg)In the back i left a big hole...

... you want. There is also a 4" tweeter (shown printed next to the midbass speaker) for those that want something more obviously visible. ... The main picture you see shows the digitally painted versions of the actual STL's you are downloading.

**Compatibility** 2012.5 - 2019 Porsche 911 (991) - fitment unconfirmed 2013-2016 Porsche Cayman & Boxster (981) **Tweeter** [Morel MT450](https://www.crutchfield.com/S-fBwvuENEM1V/p_210MT450/Morel-MT-450.html) **Hardware** 4x Screws - McMaster-Carr...

Three iterations total, v0.1 & v0.2 exist only for refining the final product and will not be uploaded. Fits quite snugly into original cutouts and uses the same hole pattern. I used hot glue to both hold the tweeters in place and as vibration...

This plate allows for replacement of the driver with a component tweeter of your choosing. Print the parts and drill a hole appropriate for the flush-mount hardware that came with your tweeter set. If you prefer to print the part with the hole...

This is a heavily remixed version of the Snap Lid for Cascade Box by agenkin https://www.thingiverse.com/thing:4630740This lid fits a Cascade Box for 78 ActionPacks, so it can be used as an Outdoor Box to protect electrical connections from the...

Customized version of https://www.thingiverse.com/thing:26596 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=26596

This is the inexpensive piezo tweeter you can buy on Amazon or ebay for like $2.50US. The model is not highly detailed, just enough to use as a design element for fitting purposes. ... Per the Nippon catalog, 4-9Ohms, 4K-20KHz, 30/60W (RMS/Max).

This is the inexpensive piezo tweeter you can buy on Amazon or ebay for like $2.50US. The model is not highly detailed, just enough to use as a design element for fitting purposes. ... Per the Nippon catalog, 4-9Ohms, 4K-20KHz, 30/60W (RMS/Max).

I made this one-inch dome tweeter wave guide for my pioneers since the one that came with it was a total disappointment. ...The new wave guide responds to frequencies ranging from 950 Hz up to 22,000 Hz when printed with PLA and at least 25% infill (a...

Tweeter stands for Lada Kalina 1st Generation, but it may not fit perfectly. I've done my best to make it work, though. Unfortunately, it can't replicate an original fastener, so I've used double-sided duct tape to hold it in place. ... Lada...

This is an adapter for mounting a 1" tweeter on a Hyundai Elantra. My own was from a 2013 model, but it should work for several models within a few years. I used it to mount a Pioneer TS-A300TW, so you may need to adjust the diameters to fit other...

... the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended. The upper hole is meant to be used with a FlexMount20 Adapter for Tesla: https://www.audiotec-fischer.de/helix/lautsprecher/compose/flexmounts/cfmk20-tes-1

Speaker pods for DLS RC50.

A sleek and versatile tweeter stand.\r\nEasily customizable to fit your unique style.\r\n\r\nPrint with durable TPU material.

this is held on by the same bolts that hold the mirror in and if you have tweeters that have some sort of cup that allows them to be mounted from the center with a screw or rivet, you can use these. ...you probably will need to atleast modify the center...

Bracket to present the Tweeter of the Helix Pure R speaker system. The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. ...0.15mm is...

Bracket to present the Tweeter of the Helix Pure R speaker system. The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. ...0.15mm is...

Stand to present the Tweeter of the Helix Pure S speaker system. The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. ...0.15mm is...

This is a bracket designed to install aftermarket 1 inch tweeters in the front doors of fourth generation 4Runners. ... I successfully used these on my 2003 4Runner and they're functioning perfectly, so I assume this mount will work with all fourth gen...

Stand to present the new Helix Compose i7 Tweeter. https://www.audiotec-fischer.de/helix/lautsprecher/compose/i7/ci7-t20 The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the...

Fits over the tweeter mount for a Honda Accord 8th gen for aftermarket tweeter installations.

motor pod for the Spirit poded cars.Has 4 improvements over the original: 1-it is stiffer 2-it has adjustable ride height 3-it accepts spherical busings 4-it accepts flat motor too