tv riser 3d models

Went into Tinkercad and developed these TV risers about 2" tall (in total) with about 1.75" rise for the TV as I designed the feet of the TV to recess into the riser. ... The only thing I still want to add is a rubber pad or something on the bottom...

A monitor riser for elevating a Series 6 Samsung TV.

Designed this simple riser to slip under the feet of my Samsung TV (6 Series LED Model). I made these because the Yamaha Soundbar I have in front of the TV blocks the IR signal for the remote while you're sitting. It might be a good idea to use some...

The recessed area to fit the TV foot is 9.25" x 1" the lift distance is .875" Measure your TV feet to check. You can easily scale this up or down in your slicer by height, length, or width. This took about 30 hours to print, it has 20% infill. Figure...

Designed this simple riser to slip under the feet of my Samsung TV (6 Series LED Model). I made these because the Yamaha Soundbar I have in front of the TV blocks the IR signal for the remote while you're sitting. It might be a good idea to use some...

I made these because the Yamaha Soundbar I have in front of the TV blocks the IR signal for the remote while you're sitting. It might be a good idea to use some anti slip mat underneath since it slides more easily with risers installed. However, I...

The OpenSCAD file has been designed to be highly customizable - you should easily adjust the height or length of the riser. I rotated the object to print without any supports needed. ... You will need to print four of these; I used 30% infill for PLA...

... on my Samsung UHD TV. ...To solve this problem, I created a custom solution - a set of feet designed to be placed under the stock Samsung legs to elevate the TV approximately 35mm, thus freeing up space for the IR receiver to function properly.

... replicas of this layout to elevate my 50-inch Vizio television by 2.25 inches, allowing me to accommodate my speakers beneath it. ...These supports could also be utilized to create space for a gaming console or another item directly below the TV.

I am using these four blocks of PLA to raise my 55-inch LED TV by three inches so that I can fit my center speaker underneath it. That's been a game-changer, let me tell you! Thanks for your help and stay safe. ... By the way, Thingiverse isn't working...

Si vous n'avez pas d'imprimante 3D et que le produit vous intéresse, rdv sur Etsy ou vous pourrez passer commande :...

Riser for 2019 model LG 43UM7300PUA TV. Wanted something to lift it up higher than my Energy Center-channel speaker so that it won't block the screen nor the IR receiver. ...

[protius2](https://www.thingiverse.com/protius2/designs) made this [television lifting shoe](https://www.thingiverse.com/thing:4719496) for the same TV but it was too tall for my needs. I downloaded the stl and re-made the model to the same...

The Hisense HS214 soundabar doesn't quite fit between below the Hisense 43" Roku TV (why Hisense, why?) so I needed a part to raise it up.protius2 on thingiverse made this television lifting shoe for the same TV but it was too tall for my needs. I...

3 piece ikea tv stand riser, raises the stand about 6 inches

200x200 VESA riser/stand for tv/monitor intended to let the display lay flat on a table while giving clearance for power cables.We recently started playing D&D in person and we busted out an old 40 inch LCD tv he had laying around for the map. We...

So I wanted to place my soundbar directly under my standing flatscreen tv but it did not fit and came up with this. I did put some sheets of rubber (cut from an old bicycle inner tube) under it to make it more stable and less likely to shift. ...

J'avais besoin de supports pour surélever ma tv 65 pouces Philips afin d'installer une barre de son dessous J'ai créé un tunnel et une encoche sur le bas du support afin de pouvoir faire passer les cables de la barre de son et accessoirement...

This is a riser voor a Samsung TV. This was necessary because the supplied stands were too low in combination with a soundbar. The parts raise the TV 4.5cm. ... The model in the pictures is ue32j5200aw.

To elevate the TV, I crafted four simple yet effective risers. The fill density may be low at 0.1; however, for safety, I recommend using 0.3. ...With this density, my 90 kg weight is securely supported on a single riser.

This is a riser for a Samsung TV. It had to be done because the included stands were too short when combined with a soundbar. They elevate the TV by 4.5 cm. ... The model shown in the images is UE32J5200AW.

... home theater speaker system, however, it was incompatible with my television due to its uniquely designed pedestal base and oversized footprint. ...To rectify this issue, I created custom risers that provided an elevated platform for my television.

This is specifically for the LG 49UM6900PUA. ... It raises the TV up 34.75mm Each leg that this is designed for is 235 x 16mm. ...This landing zone is 236.5 x 20mm

In my case I use the TV's for side PC monitors and wanted to raise them to be level with my actual gaming monitor in the center of the two. By default, these are .625" high, but you can scale the model in your slicer to where you need them to be....

A custom stand for the XiaoMi 33" TV Soundbar is available.\r\n\r\nWith an adjustable tilt of 10°, it's ideal for those with a low-set TV who want the soundbar to direct its audio straight at them.\r\n\r\nThe stand fits snugly into the socket by...

Simple TV stand - the new soundbar required more space... ...Designed for Panasonic TX-58JX800.

150mm high, 30 mm tall, can be scaled according to your needs. ... The size of the board on the photo is 800x200x16 mm. The TV weighs about 6 kg

Customized version of https://www.thingiverse.com/thing:5245416 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5245416

I decided to design new base legs for my son's TCL 43" Roku TV, as the original ones were too short to accommodate his Xbox One and cable box underneath. ...Using my Ender 3 Pro 3D printer, I created custom 70mm tall legs that fit perfectly onto the...