turn x 3d models

You also need to turn on solid infill every layer to avoid something called infill anchoring, which divides up the infill into ugly pointless zones (in PrusaSlicer). That will not look good in the transparent layers and needs to be bypassed. This can...

You also need to turn on solid infill every layer to avoid something called infill anchoring, which divides up the infill into ugly pointless zones (in PrusaSlicer). That will not look good in the transparent layers and needs to be bypassed. This can...

The drone and blowpipe stocks are traditionally tied in when the bag is inside-out and the chanter stock is tied in after the bag is turned right-side-out. Make sure you don't leave any gaps. Even a small leak will make playing the bagpipe much more...

!                                                          1, Import RED or WHITE file   ...

Alexander was so amazed of their beauty, when he saw the birds in India, that he threatened the severest penalties for any man who slew one.[33] Claudius Aelianus writes that there were Peacocks in India, larger than anywhere else[34] One myth states...

Then, you can enter the data displayed in the name tag creator (width x depth x height) into the coaster generator. If you're using rounded corners, enter in the coaster generator the data used for the frame corners in the name tag generator, not...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Avoid lifting and warped prints!There is a small amount of support needed - "for support enforcers only."Under the elevator shaft on the Middle Floor and Top Floor.The elevator door on the base floor.Increase the size of your “Dice Tower - Building...

Some igniters are meant for different kinds of motors and you might get a surprise if you use the wrong thing. Surprises are bad, plan everything.Pick your launch site carefully, you usually need a half mile radius or so when launching unless...

A few months later I created and uploaded a similar design for the larger and quieter Noctua NF-A9x14 fan (92x92x14mm - it may or may not fit into your printer) - make sure to check out that alternative too before you settle on a...

The hot end lock fits 16mm OD with a 11.9mm OD x 5.7mm tall channel, and the design is sized to expect 51.25mm (-1/+whatever) from the top of the heat break down to the top of the heating block. I don't know if this'll fit an E3D V6 or not, but I'll...

Once the correct amount is placed (making sure you can still mount the motor), you can fix it by gently dropping some epoxy over it.You'll also need 8 pcs of neodymium magnets for the cabin/lid.8 mm diameter 3 mm thick, like these...

Then, you can enter the data displayed in the name tag creator (width x depth x height) into the coaster generator. If you're using rounded corners, enter in the coaster generator the data used for the frame corners in the name tag generator, not...

Create your own version with these options: qr\_y=0, qr\_x=0, tag\_height=80, tag\_width=80, perimeter=-1000, corner\_radius=10, case\_thickness=1.8, hole\_r=10, hole\_y=0, hole\_x=30, per\_h=10, per\_w=3, obj=1, add\_sub=1, qr\_size=33,...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

That's because of its spin direction and the right hand rule, the south direction of the rotational axis is pointing almost directly to us. The file's names explained: name_1_x_10_y.stl is 1 : x * 10y. So _1_6_10_7 is 1:600000000 or one in 60...

Install the grip with two M4x16mm screws (do not forget to insert M4 Hex nuts into the back part of the grip).         [red] thin wall must be oriented to the longer side of the glass panel.[green] Inside...

float is symmetrical and the print is centered).You can scale it freely (as long as X and Y have the same scale-factor), but the holes will also scale. There's a half-size version included too (with full-size holes), you can scale from it or the...

The file's names explained: name_1_x.stl is 1 : x. So _1_500 is 1:500 or one in five hundred. <br><br> I spend part of my time making these models, letting them available and free for everyone. ...If you want to support my work, you can contribute...

All three moons of it are too small to make in the same scale. The file's names explained: name_1_x_10_y.stl is 1 : x * 10y. So _1_6_10_7 is 1:600000000 or one in 60 million. <h4>130 Elektra</h4> This big asteroid with a pretty fast rotation...

There are many scenes that the Citadel is seen completely from the outside (s1e10, s3e1 and s3e7), but it's always the same shot, at the same angle, so some parts, their size and/or shape, are highly speculative, specially in the lower part. The...

I did not contributed on doing the original file from the collection of asteroid radar models of the PDS site, I just simplify and softened it using Blender. The file's names explained: name_1_x_10_y.stl is 1 : x * 10y. So _1_6_10_7 is 1:600000000 or...

You could use larger sheets of adhesive tape, however, they are a lot thicker @ 0.5mm (the 235mm glass does not include thermal adhesive tape)....

I used GIMP instead of Paint.net for drawing the topography; Octave instead of MATLAB for plotting the 3D model; MeshLab for simplifying the meshes, instead of Microsoft 3D Builder; Freecad2 instead of SolidWorks for the tunnel and the World Engine;...

Instead of being part of the fan duct (weak and difficult to focus), I created a hinged mount that connects to the Prusa X stepper motor. If you decide to use this option you should use it in combination with “Cooling duct with...

In addition it contains two zip file containing the parts STL files used to build the combined ships and the Blender files used to create those parts: - ...

The smallest scale (1:1000) has the ramp fixed, so I didn't splitted it. The file's names explained: name_1_x_10_y.stl is 1 : x * 10y. So _1_6_10_7 is 1:600000000 or one in 60 million. <br><br> I spend part of my time making these models, letting...

Using the following options: qr_thickness = 5, code_flip = 0, perimeter = -1000, qr_rotate = 0, qr_scale = 1.6, qr_bottom = 1, tag_thickness = 3, case_thickness = 1.8, tag_width = 70, tag_height = 50, hole_r = 3, hole_y = 18, hole_x = 30, add_sub =...