tubing straightener 3d models

Brake line tubing straightener

This tubing straightener is designed specifically for copper tubes measuring 4.8mm in diameter, commonly used in car brake lines. To assemble this device, you will need a total of 24 components: eight 608 ball bearings, eight M8 screws, and eight M8...

Coiling unwinder for 1/2" to 8/16" thick copper wire.

Tool to straighten 3/8" copper coil. Two parts. One printed 3x over and the other printed 9x over. ...

Initial build is set up for 3/8" soft copper tubing, which was able to straighten very well from a coiled roll. Uses 5x 608RS generic cheap bearings and M8 hex bolts. Use long shank bolts between the top and base to maintain alignment. Printed in PLA...

This is used to straighten a roll of aluminum tubing used for compressed air installations. These are expensive to purchase and when you only need it for a single project in makes sense to print one! The wheels are mounted with 10mm hardware. I...

Trying to straightening it by hand is impossible. Amazon has a handy tool which I thought one could design something similar and print it.  This is the result. ...I added a fun name which is clearly not required.0.4mm nozzle was used.The main body was...

... 16) and the bolts are M8X20mm Flat head bolts (quantity 16). The small washers go on each side of the bushings. Check out the demo video - https://youtu.be/mGnNRnLcs7U QTY 16 - Tube Straightener wheel QTY 32 - M8 washer QTY 4 - Straightener Bracket

Everything else stays the same from ["3/16" Tube Straightener by njmcpherson"](https://www.thingiverse.com/thing:4754659) including assembly. Worked perfectly! ... Get the bearings I used: [Click...

... always get stuck on an edge inside of the Heatbreak when the PTFE-Tube didn`t align perfectly in line with the Heatbreak. So I designed this simple part to straighten and align the PTFE-Tube in line with the Heatbreak. ...And now it works just fine.

... of the bent area while rotating the tube the whole time. Should take a few minutes but it will straighten out the charging tube no matter how hopeless it looks. ...I printed mine w/ 4 walls and 40% infill but im sure other settings will work too.

Straightener for various size PTFE tubes or filaments. Just print two of the same length, rotate one at the 5 or 10 cm point (middle) and they should engage. ...The small slits allow for a bit of flexibility while assembling it around a curved filament...

Have you ever been frustrated by the 'out-of-round' toilet paper center tubes that can stop the roll from turning smoothly...especially in the more compact holders? This is a simple tube designed to fit the center tube of most toilet paper rolls...

Tested with Aluminum tube and it works great. likely works with stainless or steel. Print 3 of these with PLA and assemble into a triangle looking thing. Use 17x40x12 bearings and wood screws to hold it together. Use extra wall loops (2+) so...

This is a small hand operated tool I designed to be able to straighten capillary tube that usually come in loop. ... The wheel should be a little loose, and the two plates friction fit together, you might need to modify the diameters.

What are different in this remix : the bowden straightener region is now circular, in order to straighten the tube during printing in all surface of the building platform, especially the back area to avoid flexion of the bowden and reduce friction...

Tube straightener for Maxline 1/2 inch diameter aluminum sleeve tubing. Mounted wheels to 18 mm plywood. Used twelve 3/8 inch x 2 inch carriage bolts with one washer and nylock nuts. Spaced 30 mm horizontally and rows 52 mm vertically apart....

Von den gedruckten Teilen werden folgende Stückzahlen benötigt: You will need this amount of the printed parts: - 8x Rohrrichter 110 - 16 /or Rohrrichter 110 - 20 /or Rohrrichter 110 - 26 - 3x Rohrrichter-Abstandhalter - 2x Positionierring...

Straightening tool for tube with a diameter of 16mm This is a tube pipe straightening tool that I tested only with multilayer plastic tubes, it is designed for tube pipe with a diameter of 16mm. I was afraid with printed bolts and nuts, after all it...

Straightening tool for tube with a diameter of 16mm v2 This is my tube straightening tool version 2 ([version 1 here](https://www.thingiverse.com/thing:4146178)) that I tested only with multilayer plastic tubes, it is designed for tube pipe with a...

Straightening tool for tube with a diameter You need to buy :12 ball bearings 608ZZ (8 x 22 x 7mm)12 nuts M8 + 12 bolts M8 35mm length + 12 washer M8This update add some improvements from original :Diameter can be adjusted to 20 mmA funnel was added...

Credit to: TheJaf for inspiring this design Originally designed for straightening 1.7mm capillary tubes used for cooling/AC. Can be adapted to straighten any thin tubes/solid core wires. Requires two identical halves to be printed and joined with 5mm...

So I created this cover/straightener, pretty much like a hexagonal drinking straw, that slides over the drip irrigation line to keep it straight (and also protected from damage such as solar UV and shovel nicks). I used a pentagonal design which...

I required a tool to straighten some Copper and alloy bundy tubing. searching online i found various deisgns but nothing suited my needs completely and i needed to do multiple sizes. So i designed this tool and 3d printed them. all working 100...

I recommend using a 1mm drill once the print is finished otherwise the pins are too tight.

To ensure that your written content is properly aligned, you should use a straightener tool to correct grammatical errors and maintain clarity. This will help improve the overall quality of your writing and make it easier for readers to understand...

A device designed for straightening bent or misshapen steel bars, ensuring they maintain their intended form and function in construction projects. ...This equipment is essential for maintaining structural integrity and precision when working with metal...

Straightens your cables.

3D hair straightener