ttgo t camera 3d models

Another triumph for the TTGO T-Beam Version 10 (1.0), engineered specifically for mapping on the TTN network. Key highlights include: - Engineered for v10 revision, where the Lora-Antenna connector has been relocated. - Tool-free lid installation,...

This is yet another case for the TTGO T-Beam LoRa board with GPS. This one fits my board which is labeled T22 V1.1 20191212. I added an additional angled face on the bottom of the case so that the screen faces nicely upwards. The input button...

I also included a model I drew of the TTGO T-Beam V1.1 that can be used for help designing cases if anyone else wants to take a crack at it. Note: The parts need to be printed in the orientation shown on the photo. ...Also, the tabs that hold on the...

This is a case for the Lilygo TTGO T-Beam (I think all models) with a 2.4" OLED I2C. ...I made a little bracket to mount the T-Beam on it, you don't have to glue it in the case.What you need:1x Lilygo...

This is a case for a TTGO T-Beam V1.1 M8N & SX1262 for use with the Meshtastic project. ... See also: https://www.meshtastic.org/ https://github.com/meshtastic Items used for this project: * 1x [TTGO T-Beam V1.1 M8N &...

In this set you find: * Lid without letters * Front Face in 3 designs: without SoftRF letters, just the hole for battery LED, and a plain version * OLED front without letters Update March 2018: * Lid without letters and cover for the antenna Thanks...

Mount desigend for low end 3D printing for panel mounting a TTGO ESP32 with a display. A rough, oversized hole is to be made in the panel. The mount side is glued to the inside of the case; the bezel is glued to the outside after mounting the...

Build your own GPS LoRaWAN Tracker. This housing is handy and suitable for the TTGO T-Beam Board (rev0.9 and rev1.0) Choose a top and a body from the matching parts for your board version. Depending on the placement of the antenna choose the...

This housing is handy and suitable for the TTGO T-Beam Board (rev0.9 and rev1.0) Choose a top and a body from the matching parts for your board version. Depending on the placement of the antenna choose the appropriate cover. Additionally you can use...

This housing is handy and suitable for the TTGO T-Beam Board (rev0.9 and rev1.0) Choose a top and a body from the matching parts for your board version. Depending on the placement of the antenna choose the appropriate cover. Additionally you can...

Case for the LILYGO TTGO T-Call v1.4 (ESP32 + SIM800L module; see e.g. here: <a href="https://de.aliexpress.com/item/33045221960.html)">https://de.aliexpress.com/item/33045221960.html</a>) and antenna (see e.g. here: <a...

Doorbell enclosure for the TTGO Esp32 Camera, PIR and Screen combo. The enclosure has a built in button for the doorbell as well as a buck converter. ...I power mine directly from the ac doorbell transformer with a simple rectifier to get the full...

This is a remix of tpatrickwalsh's TTGO T-beam v1.1 (and v1.0) case (https://www.thingiverse.com/thing:4753247), modified to fit the bigger GPS antennas for better reception.I have found that the bigger antenna is a must, as the smaller one is pretty...

This is a remix of tpatrickwalsh's TTGO T-beam v1.1 (and v1.0) case, modified to fit the bigger GPS antennas for better reception. I have found that the bigger antenna is a must, as the smaller one is pretty much useless if it doesn't have a...

This is a remix of tpatrickwalsh's TTGO T-beam v1.1 (and v1.0) case, modified to fit the bigger GPS antennas for better reception. I have found that the bigger antenna is a must, as the smaller one is pretty much useless if it doesn't have a...

This case is designed specifically for the TTGO T-Beam LoRa board featuring a built-in GPS chip. Available in multiple versions, this particular iteration is the latest (T22 V1.0 20190612).\r\n\r\nThe case boasts a screwless design allowing you to...

There are two alternative designs available: OLED lid for a 0.96" I2C display and Battery body for accommodating a 402030 Li-Ion cell and/or an I2C BMP280 barometric pressure sensor under the T-Motion board. ...If you're unable to print these parts...

Case for [ZigStar LilyZig](https://zig-star.com/projects/zigstar-lilyzig/) Original design by [Sergei Antoshkin](https://t.me/ASK_SIB) I just made a little remix: 1. Increased the slot for Type C 2. Removed the hole above the LEDs, but added a vent...

I remixed the model so it fits when an OLED display is soldered directly to the board pins.Changed the diameter of the screw holes so that 3mm screws can be used.Added spacers for greater stability.I printed the front with the display side up, with...

Modified OLED front to allow for more rectangular inexpensive 0.96" OLED boards Print instructionsCategory: Parts Summary Modified OLED front to allow for more rectangular inexpensive 0.96" OLED boards Print Settings Printer Brand: Ultimaker...

The T-Beam is aligned with the case through the use of a brace below the PCB, which locks it into place on the mounts so that there's no sliding around. A spacer on top of the PCB is used to ensure the right distance between the OLED screen and the...

Website: http://github.com/lyusupov/SoftRF **NOTICE**: This design is applicable for pre-production sample of the [**T-Echo**](https://s.click.aliexpress.com/e/_9wz3pJ). Other revisions may or may not match. It is designed to fit for a [40 x 30 x...

if the pins of your antenna don't allow for this, you'll likely need to trim that arm back so it doesn't run into the pins, and if the antenna holder winds up moving too much without this, you may want to find an alternative way to secure the antenna...

This turned out to be something of a blessing, since it also turned out that my preassembled screens weren't mounted squarely, so even if the hole was the correct size, it wouldn't have lined up correctly with my screen. I ordered my boards (915Mhz)...

Thanks to Rat_Patrol for the original design, this is a remix I did adding: 1. Support for larger GPS antena https://es.aliexpress.com/item/32813737064.html?spm=a2g0o.order_list.order_list_main.33.76da194dZPyHvG&gatewayAdapt=glo2esp 2. Mini...

IoT Support board

reeemix

Mount a standard camera securely using this straightforward T bracket designed specifically to fit perfectly on a 2020 profile frame.

The t-slot allows the camera to be positioned in a stable position irrespective of the camera's centre of gravity. The range of positions is limited to +/-45deg roll and pitch in 11.25deg intervals. Print Settings Printer Brand: MakerBot Printer: ...

The middle of the T-slot needs support, so use a standard 1/4-20 UNC thread bolt that is about 25mm long to secure your camera. ...I discovered that adding a small rubber washer on the bolt between the camera and the stand makes it easier to lock the...