ts100 case 3d models

The TS100 soldering iron stand that I printed kept tipping over, so I made this hollowed out version with a plug, so I could pour in some silica sand for the additional weight. ...I also made the tip cleaner hole bigger (⌀68.5mm)</p> <p>You can also use...

This stand is specifically designed for the TS100 soldering iron, and I've included a tip cleaner as an added feature. The washer has a diameter of 26.5mm and a thickness of 2.5mm, allowing for adjustments to be made directly within the source file...

## TS100 Iron Holder for Weller WLC100 *** ### __Usage__ This soldering iron holder is meant to attach to the Weller WLC100 soldering station by clipping over the right side at the front and then sliding back to the desired position. It is designed...

This was heavily inspired by [mightynozzle's TS100 Soldering Iron Holder Station](https://www.thingiverse.com/thing:2385609), [urw's Dewalt Battery Adapter](https://www.thingiverse.com/thing:2435964), and [maglub's DeWalt battery...

##### Update 2017-12-01 - Major Safety Fix Top lid is now flipped, and tip clips are shortened by 1mm, so the tips would not come in contact with the soldering iron case under any circumstances. There has been reported one casewith the previous...

So I think it's better for you to power up the converter unit first and then connect the TS100 after the output voltage is stabilized. ... 40mm fan grill can be found here: https://www.thingiverse.com/thing:933789 **BOM: Switch:**...

The TS100 Soldering Iron is an absolute gem. Its compact size belies its incredible power and impressive array of features. Nevertheless, the basic set didn't come with a box or a stand, leaving me scrambling for a solution that could also...

Skadis mount for Pinecil.TS100 fits too, it's more wiggly than Pinecil, but won't fall through. PrintingThere is no need for excessive infill in the holder itself, but it's needed in the hook. My settings:holder with 5% linear infill and 2 wallshook...

I bought the super practical TS100 soldering iron and wanted to use it with the existing Bosch Power4All 18V batteries from the Green Series. I then built a box that can hold the soldering iron along with four more tips, a brass brush, the connection...

Human: Holds a TS100 vertically when not in use, a reel solder dispenser which fits rolls of solder up to 40mm wide and approximately 16.5mm wide, 4x TS100 tips, and a YH-08B compact tip cleaner that can be found here -...

This holder is specifically designed for the TS100 soldering iron. It features a heavy bottom component and a detachable vertical section. This design allows the holder to fit perfectly into any box and stand solidly on my worktable. To add weight...

Two washers is added during the print that holds the TS100 iron securely.Pause at layer 93 (18.60 mm) and 223 (45.60 mm) to add the washers. ...Printed with a brim.</p><p><strong>Parameters in fusion360</strong></p><figure...

It has become an essential TS100 on/off switch, and it's also great for using a smoker since it allows quick disconnection if needed. *** Materials Needed: 2x 2mm Nuts 2x 2mm x 8mm bolts (optional, but fits snugly without) 1x XT60 Male Connector...

... keep the edges that slide in, you can modify it to your needs. I'm planning to make an expansion with retracting cable for the TS100, a place for the metal sponge to clean the tip, and a place for the soldering wire roll. ... Have a nice print!

After using a popular TS100 soldering pen holder (ref. <a href="https://www.thingiverse.com/mightynozzle">mightynozzle</a>, ID 2385609), I found that I didn't need the sponge or the variable angle. Clumsy as I am there were also a couple of...

I needed a TS100 Holder specifically designed for my Makita XT Batteries. The holder itself isn't perfect yet, as the copper tube gets too hot, so I'll probably swap it out later on. As a Solidworks beginner, my design might not be the best. You can...

... the BN 880 Q version are designed to be 2mm smaller than the standard size. For easy printing, I included this design. It can be used in conjunction with a kids' coloring pen case (as seen in the picture) or any other case that will fit as a pole.

You can print the "Single" version wich is all in one pice or all 3 other to have seperat pices (in case, "Socket" has to be printed twice) For each socket you will need a spring of 80mm lengt, 10mm outer diameter and 8mm inner diameter. if your...

Incidentally, I chose this modified design for my case (www.thingiverse.com/thing:3511257), which is itself a remix of a remix. It's not uncommon for multiple iterations to lead to a superior product. ...The original idea behind it can be found at...

Soldering iron stand ts100 for 18V AEG battery.

A holder for a soldering iron like the pinecil, ts100 or ts80 using a copper cleaning sponge as ballast. **Pro Tip:** Use double sided tape to secure the sponge container to the base. As it is the ballast, the holder __will__ fall over if you only...

Here's What You Need: A Mini STC T12 Kit without a case, which can be found on eBay or AliExpress (dimensions: approximately 2.5 inches x 2.6 inches). A 5mm DC plug. Some UHU glue or epoxy. Follow the cutting and assembly instructions in the...

... You can also check out my Fume Extractor and TS100 Case here https://www.thingiverse.com/thing:3107668 & https://www.thingiverse.com/thing:2745774

TS100 soldering iron and two brushes (one for dust, one for flux).

This is a box to store max 12 units of tips for TS100 intelligent soldering iron.

Simple tip organiser/holder for the TS100/Hakko style soldering tips. ... There is room for 18 tips Simple thingie, might as well upload it, might help someone

Shark fin for installation on the frame series XL7. ...Designed for the installation of gps Radiolink TS100. ...Printed by ABS plastic with supports.

Support for soldering iron TS100, Ideal for hanging on any surface, a lip, a table, a frame, or a beer glass, it clips and de-clips easily.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Simple but functional soldering station