trx4m shock mount 3d models

This is a generic 5.5" by 3" mic flag for an Electrovoice 309A shock mount, commonly used by the RE20 broadcast microphone. Add a sticker for your radio station on the faces! ... You will need to add some adhesive foam on the inside edges for it to...

Holder that clips onto the Yeti Shock mount to hold your headphone. ...&nbsp;Have used this extensively for the past couple years.</p><h4><strong>Printing Instructions</strong></h4><ul><li>I use PETG but PLA should also be fine</li></ul>

A quick and dirty, yet very effective shock mount for the Samson Q2U condenser mic. Uses 5x hair tie bands, looped around the center rings. Requires 2x M3x10mm bolts and nuts to install on the Ikea Tertial movable arm work lamp.

Shocking Solution for Elgato Wave 3 Mount: Fits Wave 1 too! You'll need just four sturdy elastic bands with a diameter of approximately 20mm. ... This simple design was one of my first projects, and while it's basic, it gets the job done.

This is a simple mount for your RC car's shock absorbers so that you can easily change the oil.-----Dies ist eine einfache Halterung für die Stossdämpfer deines RC Autos, damit du den Ölwechsel ganz einfach erledigen kannst.

Inspired by the mic zoom H1 holder designed by Rukey and Rode's revolutionary shock mount, expert craftsmen carefully assemble the parts with precision and attention to detail, bonding them together with a strong adhesive that ensures a seamless...

... 100% Notes: Print with layers parallel to long axis of this part. See Also Don't forget to check out my other Blue Yeti related parts: Printed Standoffs - used for spacing shock mount inner rings Mounting Kit - side brackets and a 5/8" screw

This is a shock mount to be used on the Sony FS5 camera. With the use of standard O-rings, a shotgun microphone is suspended in the middle. ...Elastic cord can also be used instead of O-rings.The regular mount that comes with the camera often becomes...

This is a shock mount to be used on the Sony FS5 camera. With the use of standard O-rings, a shotgun microphone is suspended in the middle. Elastic cord can also be used instead of O-rings. The regular mount that comes with the camera often becomes...

This is a shock mount for a Zoom H1 Microphone, engineered to sit firmly on a desk while preventing vibrations from disrupting sound quality. To secure the mount to its hexagonal ring, you'll need small bungee cords or elastic bands. ...Meanwhile, four...

Print out the two pieces separately and attach them using two thin hair bands as a shock mount. I haven't tested this modification yet to see if it improves performance over the standard clip, but it should function well. Keep all parts from your...

Just keep all the parts form your microphone handy just in case this doesn't work. Also, you'll need to add a 1/4" - 20 nut in the base in order to mount it to a tripod. Print instructionsUnassociated tags: easy print, go mic, samson go mic, shock...

... I would probably recommend printing the ring at 100% infill for additional torsional rigidity. It works beautifully and I couldn't be happier, especially considering that it cost me $15 to make compared to $50+ for the Blue Shock Mount on Amazon.

To reduce camera noise interference, I crafted a shock mount for my Sony EX-1 microphone with a maximum length of 5 CM, though a 7 CM version is also available. This two-part design eliminates the need for support material and requires only male and...

I have a MOVO shock mount that I adapted to use with an Elgato Wave 1 mic, but it felt too floppy, so I designed a little extra support. I used a little hair band as the elastic part. Printed PLA at 0.2mm with 100% infill and a brim. ... I was able...

This is a compact shock mount designed for shotgun microphones, with the T.Bone Em9600 being its intended target, but it should be compatible with most models. The design allows users to employ a rubber band of their preference. On one side, you...

This makes it easy to remove and reattach if you want to transport just the microphone and not the entire shock mount. All you need to do is print additional exteriors! One issue with this microphone is that it's very heavy. While this contributes...

I broke the shock mount that came with the microphone, and I think a replacement is too expensive - so I created one that's probably better. All you need is a 5/8 Nut for the standard microphone stand (North America) and some shock mount elastics. 2...

A 3D image of the back shock bracket on an '08 Rabbit car.

Relocating shocks enables you to adjust their position for improved suspension articulation.

If You Already Have A Shock Mount, You Can Stick With The Original Rubber Bands Or Swap Them Out For Regular Ones, As Long As They're Taut Enough. This Is The Revised Version Of This Concept - The First One Was Way Too Bulky. I Managed To Cut Down...

This is a small shock mount for shotgun microphone. The one I made it for is the t.bone Em9600, but it should work on most. Its made so you use rubber band of your choice. On one side you can hook the ends of a small rubber band, if you dont have a...

This shock mount is designed specifically for use with the Samson Go Mic. When combined with the shockmount_monitor_cup.stl file, it can be securely clipped onto a monitor stand with an outer diameter of up to 5cm. If you wish to attach the mount to...

This is a simple but good microphone shock mount for Aston Origin. Found a few designs here on Thingiverse but i couldn't find one that wasn't to big or it needed several screws and parts to assemble. so i designed this out of what i found here...

This is a shock mount I designed for my Blue Yeti microphone. It requires 1/8" bungee cord for assembly, approximately 1-2M if you want to be safe. Using dabs of hot glue when assembling the arms to the clamps would help with assembly. NO EXTRA...

A basic fixture for securing a relay module to the shock absorber assembly of a Suzuki DRZ 400 motorcycle.

Shock Mount for Aston Starlight Mic: Inspired by Thingiverse Design Version for Aston Origin Available Here: https://www.thingiverse.com/thing:3377783 The Ring Thickness Should Match the Included Mic Holder on Aston Starlight I Had to Sand Mine...

A sleek and compact handheld shock mount specifically designed to accommodate a Rode NTG1/2 mic, also compatible with mics featuring a diameter of approximately 22mm or smaller. Fitted with a standard 3/8" nut in the base of its handle for...

A high-end handheld shock mount designed specifically for the Rode NTG1/2 microphone, although it should fit any mic with a diameter of approximately 22mm or less. It features a 3/8" nut in the base of the handle, allowing for standard mic pole and...

Inspired by Mic zoom h1 holder by Rukey and Rode Shotgun Shock Mount. ...Parts should be glued together.The tripod screw is supposed to cut itself into the hole.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>MakerBot</p> <p...