trx4 3d print

The Trx4 Sport is a force to be reckoned with on the trails, its rugged design and powerful engine making it a true off-road beast. Its four-wheel drive system allows for incredible traction and control over even the most treacherous terrain, while...

I designed this to allow driving the TRX4 with one hand. It fits under the steering wheel and is low profile to also allow normal use of the wheel. Remember to not tighten the screw all the way, otherwise it will bind the wheel. Update - 4.1.2021:...

These are spacers to go under your stock TRX4 Sliders. they are designed to be a snug fit to limit any additional movement. These Spacers raise the slider 13mm to make them nearly flush to the bottom of the chassis. you will need longer bolts 20-22mm...

Mounting Brackets for 40x40mm Fans Securely Fasten to the TRX4's Front Bumper Mount. Watch this Video: https://youtu.be/QgKw_NaY1Wk Hardware Requirements: - 6 M3*16 Screws - 6 M3 Nuts Note: For 40x40x10mm fans, brackets fit perfectly. However, for...

This is an accessory mount for a Traxxas TRX4 Defender, designed to clip onto the side of the rear body section. It enables my sand ladder to stack and attach securely using a peg. I'm currently developing additional accessories that can be attached...

Narrow flares for the TRX4 Defender. I didn't run into any fitment issues but I suggest starting all the screws half way then pushing the flares to the body. Final tighten after that. I did sand and paint mine in flat black. They have held up...

This is a differential lockout for TRX4 models with dual locking differentials. I made it because I didn't want to replace the servos, and I never used the locking feature. I didn't want to buy the replacement solid spool diff. It fits under the...

This is a magnetic body mount for the Traxxas TRX4. Fits perfectly into the existing mount. This mount is intended for bodies that are already drilled. Magnets will align perfectly with bodies that have been drilled already. Works for the front and...

Rock light buckets for TRX4 and TRX6 inner fenders Mounting is easy and intuitive.Place the light bucket onto the inner fender's rock light slot.Push fit the 5mm LED into the light bucket's 5mm hole. ...Glue or extra hardware not...

Another mod of the Trx4 sport rear suspension. I had to tinker a little, the 4th version, but I'm very happy with the result. Yes, it is a complex design, but anyone who has looked carefully will notice that the shock absorbers are attached to a...

:) It is about the idea of turning the rear diff locker on TRX4 into a dig unit - if you like the idea, support it by sending $. Yes, it is possible! The design is in testing mode, but it works on the RC car TRX-4. I can help you with setting it...

This is an ESC mount designed to be bolted straight onto the inner fender of the TRX4. The hole spacing matches up with the XL-5's, so the ESC can mounted to the same place without messing up the weight bias.</p><p>You will need 2x M3x10mm...

These supports were made to lift the front and back axel of a Traxxas Trx4 Defender RC truck for storage. I did not used the defender for a few months and the soft compound tires with extra weight in the rims had nice flat spots on them (more or less...

Print and utilize.

V2 with mounts removed for easier printing.

Print all parts and connect. ...PETG recomended.Height: 120 mm

Dachtrager Complete v3. ...Printing out parts v3.1, v3.2, and V3.2. Dachtrager Complete v2. ...Printing out parts v2.1 and v3.

Print all parts and connect. ...PETG recomended.Height: 120 mmV2 have one central support.

Print all parts and connect. ...PETG recomended.Height: 120 mmV2 have one central support.

plow frame mount left and right Print at 99% cubic infill with 3 walls using PETG

TRAXXAS TRX 4 SNORKLE 2PCS PARTS PRESS FIT EASY TO PRINT

just a more factory looking front bumper. ... i printed with i think no bottom layer and 8 walls. ...

Designed to limit the steering angle(work in progress). ...Printed at 0.3mm height, uses original screw.

... Printed on my Prusa i3 MK3S+. ...I made this a few years ago and sell it on a well known bidding site, but now I think its time to let the STL file into the world. Printed at 0.3mm and 20% infill, takes around 16 hours to print on its end. ...;ules

hi I am selling my project for a body of the cherokee kj liberty, adaptable to RC car traxxas trx 4 or even to axial or sherpa, and unique in its kind because there are no others outside of this, I printed it with a anycubic i3 mega therefore each...

One hand controller for traxxas tqi. ... U can use 1 screw 2.5mmx8 or some glue for all parts. Combine color and share. Easy to print. ... Dm on insta for any question.

It's best printed with Ninjatek Armadillo or some type of Nylon, but ABS or PETG should work fairly well too. I'd avoid PLA unless you plan on taking it easy on the rig. Best to print it laying flat, like the bed is the truck window, legs up in the...

The printed component is made of PETG with a thickness of 0.2mm. This design utilizes the existing screws from the original battery tray, eliminating the need for any additional hardware. ...However, it does necessitate relocating the battery to...

Used to replace the old part was broken, or changed to be more suitable for manufacturing stl file can print and ready to use dùng để thay thế cho gá servo cũ đã hỏng, hoặc thay thế để sử dụng phù hợp hơn cho việc độ chế xe rc file stl có thể in và...

This is a piece servo mount for plow setup.....You will need to screw the 2 pieces together using 3mm screws. ...This is to be used along with the side frame mounts for plow. Use both. Print in 99% cubic infill using PETG