trx ceiling mount 3d models

I made this for my TRX-4 with Proline FJ-40 bodykit to get the rear bumper as high as possible. ...Bottom of mount is 7mm from the chassis (5mm closer than the original mount)

not my original design but modified to accomodate a universal transfercase. ... (EDIT) the links were not spaced properly, pls check out my original design trx4/trx6 universal transfercase mount Printing:

This is just a simple TRX-4 bumper mount that centers the mount horizontally between the rails.

Rear shock mount for Traxxas TRX-4 with multiple mounting points and possibility to connect to body crossmember.

remix of https://www.thingiverse.com/thing:4282530 added mounts to fit original screws. ... Tested ok on TRX-4 Sport Front needs to be mirrored.

Want a nice, low-angle shot from your crawler? ...Here's a GoPro mount designed for the Traxxas TRX-4 Bronco 2021 (will fit others as well). ... Simple print that requires minimal support.    rabbitrc.com

This is a Battery tray for the Traxxas TRX-4, allowing you to mount & secure a 5000mAh battery up front over the motor & front wheel wells. You'll just need 4 screws & a velcro strap. I designed in some removable supports so you shouldn't have any...

This is a Battery tray for the Traxxas TRX-4, allowing you to mount & secure a 5000mAh battery up front over the motor & front wheel wells. You'll just need 4 screws & a velcro strap. I designed in some removable supports so you shouldn't have any...

This is a customized Battery tray specifically for the Traxxas TRX-4, enabling you to securely mount & position a 5000mAh battery at the front of your vehicle above the motor & front wheel wells. To set it up, you'll just need four screws and a...

Wall mount for the Traxxas TRX-4 and other similar RC trucks/cars It hooks around the rear axle of the vehicle and screws to the wall with two #10 wood screws (canada, not sure if there is a metric equivalent - 0.193"/4.9mm diameter thread). You...

a bumper mount i made to mount a trx4 bumper to gen7

a bumper mount i made to mount a trx4 bumper to gen7

... Good reasons for reloacating the servo are: - more forward weight, - prevent collision of servo horn to panhard rod at full droop, - create more space for bigger or forward mounted motors, - create space for front longitudinal mounted battery pack.

To mount the front bumper's second hole, you'll need longer screws that pass through both the stock bumper mount, the rails, and the servo mount. I repurposed screws from other areas of my chassis where plastic components were previously held in...

This premium winch mount upgrade gives you the freedom to stash your winch discreetly within your vehicle's bodywork, cleverly concealing it behind the front grille instead of proudly displaying it on the bumper.\r\nCheck out eBay for "1/10 Scale RC...

I utilize a straightforward ceiling mount bracket that requires only two M4 screws and two nuts to secure the lamp holder in place, as well as two additional wood screws to firmly attach the holder to the ceiling itself. ...To properly install the nuts...

This is the ceiling mount for the universal bracket. I have not printed/tested this yet, so print at the risk of balence isses, or the bracket not fitting correctly. ...I would use a carabiner or other to hand.

Ceiling profile leveling jig compatible with Norgips ES 60 X 250. ... Wieszak plaski

This is an easy-to-use wall-mounted planter perfect for my indoor flowers.

Dahua ceiling mount for common 2" threaded coupler. In this case I'm using it for a SD59225U-HNI camera. ...

Just a simple bumper mount delete for the TRX-4. I printed it in 95A TPU. ... Category: R/C Vehicles

My son bought a new body for his TRX-4 and the stock mount wasn't in a great spot. ... we made this mount so allow him to use the new body.

Mounting the trims, lights, and other accessories on the top rack of your Traxxas TRX-4 Defender body allows for easy removal whenever necessary to maintain a balanced load.

Magnetic mount for TRX-4 G500 (may also fit on other TRX-4 models). The front part accomodates a magnetic 5 pin pogo pin connector. https://de.aliexpress.com/item/1005001581686458.html?spm=a2g0s.9042311.0.0.105e4c4d136vPf This can be used to...

I Installed a New Mount on My Truck to Make it Compatible with the TRX 4. The Custom Mount Secures to the Lower Front Cross Bar, Perfectly Synchronized with my $20 Camera's Movement. Check out this Awesome Setup in Action!

LayDown servo mount for trx-4 . this is made for small engines. ...one is with battery holder for 3s 750mh bat perhaps it fits with the 540 engine the mount that has no reinforcement at the rear and will work with original links and servo horn and drill...

For those that have raised the body 6-8mm here's a front skid plate mount that replaces the stock front bumper. You'll reuse all the factory hardware, and installation is very straightforward. ...I recommend cutting the front bumper off and going with a...

The creator of this mount engineered it specifically to be compatible with the TRX 4, skillfully attaching it to the lower front crossbar. ...This innovative accessory performs remarkably well for its affordable price point of just $20, making it an...

This support bracket will allow you to attach an accessory to the Trak Racer TRX that would normally attach to the front mounting holes on the base of a Simagic or other DD base. The base mounting holes are 45mm apart with a 9mm hole suitable for an...

... due to excessive movement or stress. Whether you're navigating rugged terrain or simply need a reliable winch system for recovery operations, the TRX-4 Defender rear servowinch mount is an essential accessory for any serious off-road enthusiast.