trunk latch 3d models

Use for Door Cabinet....

steps:1. created left edges sketch first2. added the curves, created relations and dimensions3. worked on right side of sketch4. added hole in left center of sketch5. added finishing relations with respect to the plus reticle thing6. extruded7.

school education

a tool

I created this by measuring out the measurements on the front and extruding backwards.

Humans can easily manipulate the locking mechanism.

Step 1: the only step is too carefully sketch out the part and precisely do the correct dimensions and boss extrudeStep 2: just be carful with some of the curves when using either arcs or circles

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters

This is an easy-to-use, straightforward equipment that simplifies tasks and enhances performance. ...Its user-friendly design ensures hassle-free operation, making it perfect for those who prefer a no-nonsense approach to hardware.

Mass = 1066.52 gramsMake a sketch with a circle at the origin R6. Make a line to the left and underneath both 14 away. Make the left line 18 and between those a 45degree angle line. The bottom line running until a R5 circle's top. From that circles...

This is one of 6 original parts I used for this assembly. The only changes I made for this part were to make it smaller so it can fit the size of the rest of the assembly. I used this part to create a 'locking' mechanism for the fridge. ...I was going...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters Process:I sketched the whole part in just 1 sketch and then did the boss extrude. ...It was relatively easy it's just figuring out the dimensions.

First I made a lot of dimensions to make it easier to sketch out, I started on the right slant and worked clockwise. ...After I made the sketch I extruded 45mm.

Use for Door Cabinet....

Part was built :)

First, I started by sketching out the outline of the front view of the sketch. I used the dimensions in the blueprint to sketch out guidelines for me to use to sketch it out. I used the line tool and the center line tool the most in this project.

<p>PLA 200/60</p><p>Fan 100%</p><p>no supports</p>

Test prep project

I started by sketching out the front profile, making sure all the measurements including radius' were correct, then I boss extruded the model without including the circle.

CSWA part

Plugs that can be used on the model, positioned using rubber bands.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersI started with the circle and worked around.

Density = 0.01 grams per cubic millimeterMass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersFirst sketch your piece on the front plane then extrude it, and if need be do a extrude to next on the...

Solidworks Certification test

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersFor 2D I used the line, fillet, and circular tool.For 3D I used the extrude feature.

Tools used: Smart dimension, line tools, circle tool, trim entitiesMass: 1066.52

I simple just followed the blueprint instructions, dimensioned the figure correctly then extruded the figure to the correct measurement.

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimeters For creating this drew this out from the blueprint provide and started sketching at first the circle I did not put at the origin so make sure to do...

Mass = 1066.52 gramsVolume = 135002.52 cubic millimetersSurface area = 18681.37 square millimetersI sketched out a circle of radius 6, and a line 18mm long on the left, and then 2 of 45degree angles, make sure the center of the circle to the bottom...