tronxy x5s 400 marlin 2 0 mks sbase setup by 3d models

I kept the original display but modified it to fit the SBASE requirements by cutting notches in the sockets so the cables can be plugged in backwards. To improve accuracy and stability, I replaced the 8mm/rev lead screws with 1mm/rev ones. If you...

I've adjusted the current Marlin 2.0 Bugfix (as of 25.03.19) to fit a TronXY X5S with ABL. A firmware.bin for direct flashing is included! Board: MKS SGEN v1.00 Display: RepRap Smart AUX1: JZ Board/Fullgrafix Display TMC2208 driver in Spreadcycle...

My current config for my TRONXY X5S-400 MKS SBase Category: 3D Printers

My Current Config for My Tronxy X5S-400 Mks Sbase Mks Gen L v1.0 Stealth Chiller 100w 24v Heatsink Version BlTouch Adafruit Ledstrip 60cm with Dc-Dc Converter and Relay Board Duet Wifi 2.0 with Duex5 Board

This is the Marlin 2.0 firmware preconfigured for MKS Sbase 32-bit boards installed on stock Ender 3 printers with 1/32 microsteps enabled. The auto extruder fan operates at a temperature of 50°C, and the part cooling fan is working as expected. The...

Updated to the Marlin 2.0 for MKS Sbase board (1/16 microstepping) with filament run-out sensor (X_Max connector. Notice if the filament sensor cable might need a mod, swap the V/S pins) The following enabled Filament run-out, if not one can be...

Updated to the Marlin 2.0 for MKS Sbase board with 1/16 microstepping and filament run-out sensor connected at X_Max connector. Be aware that the filament sensor cable might require a mod or swapping of V/S pins. The following features are now...

Remix of X5S Tronxy Marlin 2.0 by SLKittie for use with a standard printer without BLTouch. The original config file was created by SLKittie and ej0rge, intended for an optimized printer, featuring non-inverted X/Y axis (invert this setting in the...

This is a Tronxy X5s Configuration file for marlin 2.0 created by me and ej0rge. Using pin 27 and making some adjustments to make room for new BLTouch code, we have to disable several options. The main ones are uncommenting SLIM_LCD_MENUS,...

I have also set MINIMUM_STEPPER_PULSE to 4 in configuration_adv.h (for MKS SBase V1.3 board): #define MINIMUM_STEPPER_PULSE 4 // Was 2 Marlin 2.0 Features I'm Currently Utilizing on the MKS SBase Board: -- Auto Bed Leveling with a Capacitive Probe...

I was tasked with crafting a mount for the MKS SBASE board on my tronxy X5s printer, and I assumed it would work just fine on other printers too. Since I don't have an MKS SBASE board at my disposal, I relied solely on the measurements provided to...

It's my first configuration and you can see how it works in this video review of mks sbase board https://youtu.be/GuHpoGUpxUg **Attention**: In this version, manual movements don't work with endstops; negative movements are allowed. I'll add updates...

...You can find their work at https://www.thingiverse.com/thing:2818468, Tronxy X5S MKS sbase config.txt by SgaboLab. This has the basic setup for the TronXY X5S config.txt. I added a bit to it and invested many hours of testing to get it working. 1.

Marlin Firmware Optimized for Tronxy X5s Printers Featuring Bigtreetech SKR 1.3 Boards and High-Performance TMC2208 Stepper Drivers

This is a Smoothieware config.txt file tailored specifically for the Tronxy X5-S and X5-ST, paired with a MKS Sbase V1.3 board and BLTouch sensor. To mount the BLTouch, I recommend using a Petsfang dual duct cooler with BLTouch mount to avoid...

A frame that perfectly matches the mks SBASE 2, accommodating either a 2020 or 8020 setup - I've successfully utilized it with both configurations.

I have designed a display mount specifically for use with the "Tronxy X5S" and an "MKS TFT 32_L V3.0". To attach the display to its bracket, you will need four M3x10mm screws and four M3 nuts. For attaching the display bracket to your Tronxy...

Tronxy X5 Marlin 2.1.2 hybrid for MKS Gen L V1.0 board. Upgrade your Tronxy x5 using gen L v1. board by MKS. No issues with stepper control for now. A4988 and LV8729 Drivers used be sure to correct to the right ones !!! Don't forget to calibrate...

Control panel for TRONXY X5S-400: Mounting points provided for: • 1 - MKS v1.4 • 5 - TL-Smoother • 1 - MOSFET

Control box for TRONXY X5S-400 Mount points for: 1 - MKS v1.4 5 - TL-Smoother 1 - MOSFET

This profile was printed using Marlin 1.1.8 firmware (available at http://www.customize-3d.com/tech/flashing-tronxy-x5s-factory-control-board-usb-cable-only.html) after I had tuned both the bed and hotend for optimal performance. ...The prints were...

This is the casing specifically created for the MKS Sbase by MKS themselves. ...It was obtained directly from their official Chinese customer support team via QQ messenger.

After receiving my Tronxy X5s, I discovered that the belts were misaligned. I searched online and found that numerous users had created belt relocation designs, but they seemed overly complicated. I decided to simplify the process by designing a more...

Large storage tray for x5s 400

Support for MKS Sbase 1.2 on frame 20x40 Print Settings Printer: C-Bot Rafts: No Supports: No Resolution: 0.2 mm Infill: Fifty Percent

This is the final Marlin 1.1.9 configuration for my highly customized TronXY X5S.\nIt serves as a companion to my in-depth blog post on setting it up: https://burningbecks.wordpress.com/2018/09/29/marlin-1-1-9-on-tronxy-x5s-melzi-style-board/\nDue to...

Modified Marlin 1.1.9 for Tronxy X5S This firmware optimizes memory usage for SD and LCD, aiming to smooth out step motor performance. ... Firmware in zip file Update 12 Aug 18 - Step motors X Y now produce significantly less sound than before,...

Marlin 1.1.8 for TronXY X5S, fully functional!\r\n\r\nThis version includes all the enhancements made to the original stock 1.1.6.\r\n\r\nIf you want to stay up-to-date with the latest Marlin developments, this is your best option.\r\n\r\nThe way...

I have a running Marlin 2.0.9.2 firmware on my Tronxy X5SA with v6 20xxxx board. ! USE IT ON YOUR OWN RISK ! ! I do not take responsibility for any dead or burning printer ! The Uploaded ZIP contains two .cbd update file, BUT BEFORE you update...

This is a customized version of the standard Marlin 1.1.6dev firmware for the TronXY X5S printer. I have made numerous small enhancements to improve overall performance and user experience. Manual Mesh Leveling has been added, utilizing a 4x4...