trolling motor steering bracket 3d models

Steering bracket made for Minn Kota. Tested on Minn Kota 36lb and it works perfect. ...Print it as follows: PETG 230/ 75 temp 100% Infill Supports not required, but you can put them if you want.

This thing was designed using Tinkercad and can be modified directly online at https://www.tinkercad.com/things/hMv7x5IxEVq.

Minn Kota Trolling Motor Shaft Steering Bracket

Unlike other mounts that demand disassembling the entire trolling motor, this clamp design offers a hassle-free installation process. ...Feel free to fine-tune as needed; I suggest bolstering the wall count where pressure is applied for added stability.

I needed to modify it to fit my Watersnake 24lb motor which has a different size shaft (25mm) and location for the locking nut. I also removed part of Theo's design and trimmed it down to only the holder for the servo, as my electronics are...

****UPDATE*** as many requested I change the gape on the screw side to 3mm I needed a beefier kayak trolling motor steering so i designed this one for my minn kota Endura C2 to install on my kayak it fit any trolling motor with diameter of 1.125" or...

This is a trolling motor steering that is compatible with a NK-180S trolling motor, I designed this for a kayak, but can be used for any thing it is needed for.

 Kayak trolling motor steering for 32mm shaft ommended filament is PETG/ABC/PCI`ll be printing it at 100% infill because as I mention above i need beefier steering for my self, but it should be fine at 20% PlusPrint SettingsPrinter...

trolling motor tilting lock lever pulley for YAKoholic steering with 32mm trolling motor shaftThanks to Chris Hart for sharing picture of his trolling motor tilting pulleyI included the picture he shard to have a better understanding of this trolling...

Mount for attaching Humminbird or other fish finder/dept finder transducers to a Minn Kota or similar trolling motor with a 3.5-4 inch motor diameter. Use 3M VHB backing between the motor and mount, securing it with a 4-5 inch hose clamp typically...

Quick release bracket, compatible with Xi5, BLX65 and B*ltema Electric Outboard Motor3D Printed bracket to store the bow-mount motor on the wall.

I made these bushings for the clamps and spacer for the bow of my Jon boat to mount a Minn Kota transom mount trolling motor on the bow. This specifically fits the Lowe 1448 hull, but may fit other models too. I was replacing a wood block that was...

this is Kayak trolling motor steering for 26mm diameter shaftmy recommended filament is PETG/ABC/PCI`ll be printing it at 100% infill because as I mention above i need beefier steering for my self, but it should be fine at 20% PlusPrint...

Trolling Motor](https://www.amazon.com/Newport-Vessels-Saltwater-Electric-Indicator/dp/B07454VQ71?th=1) on my Bonafide RS117 kayak, but holding my arm behind my back to control steering & throttle was uncomfortable. I can't use a pedal steering cable...

Building it was a challenge, using materials I had on hand, such as a brushed motor and a broken cordless drill. I'm still working on perfecting it, but it's almost ready for its first test drive. Here are the results of a quick control test from a...

trolling motor pod, utilizing a smaller diameter, but longer internal motor and an internal impeller. ...still have some components to add including the shafts and a flow straightener.

I attached this printout to the handle of my trolling motor, making it possible for me to maneuver the kayak from my seat with effortless ease.

This is a steering bracket I made for my buddies kicker motor on his boat. It's all SS hardware and I used .125" thick SS plate. ...It's been installed for like 5 years now and going strong.

yakoholic trolling motor in steering 2 section for minn kota Endura c2 I needed a beefier kayak trolling motor steering so i designed this one for my minn kota Endura C2 to install on my kayak it fit any trolling motor with diameter of 1.125" or...

Bow Trolling Motor

trolling motor impeller

This creation is brought to life with Tinkercad's innovative design tools. ...Make adjustments and tweaks online at https://www.tinkercad.com/things/7zK6mD9tN8R

scaled this up in tinkercad to fit a 25mm shaft. ...watersnake 18t or anything with that size shaft

This creation was designed utilizing Tinkercad's intuitive features. ...Refine and customize it effortlessly at https://www.tinkercad.com/things/g8zX6cGwH0y.

I needed some extra control over my trolling motor when it wasn't running, so I could steer easily even without electricity. With power on, the motor guides me smoothly in the right direction, but as soon as I shut off the engine, I'm completely at a...

I wanted a little rudder on my trolling motor, so that when I'm off-power I can still use the motor to steer. When you're on power, the motor works well to point you in the right direction. When you're off power, you have no control. They sell a...

Mounts for attaching a fixed rudder made from a 1/8" thick cutting board to a trolling motor with options of a 1" or 1-1/8" trolling motor shaft. 01/23/2022: Revision 1: Added files for using a 3/16" thick cutting board (designation is 1875) on a...

this is trolling motor shaft endcap for kayak the design adopted from the youtube video in the link https://www.youtube.com/watch?v=M3DIUbQCLGw

A mini trolling motor features an automatic trim function, allowing it to be easily mounted at the back of the boat's hull. ...It can be controlled effortlessly from a distance using a joystick for convenience and ease.

The trolling motor is based on the Motorguide Xi5 model. Since there was no requirement for textures, the client provided a simple gray image. ...If you need it in a different format, please let us know.