tripod mount for cell phone 3d models

This cold shoe mount lets you attach accessories to your camera tripod, e.g, a shotgun microphone for movie recording or and external monitor. I attached it by tapping two M3 blind holes on the side of the ball socket. This mount was designed for my...

This model is a mount for the c270 Logitech camera that is compatible with the @MatveyKukuy's wonderful fully printable tripod.Supports: yesRaft / Brim:  noThis mount attaches directly on the tripod base and not on the ball connector or other...

... you need is a common 1/4'-20 nut in the bottom of the holder. ...I deliberately made it a bit bigger to attach sports tape or thin soft foam for extra grip on the phone, but if you prefer a tight fit scale down by about 2 percent and you'll be golden.

The original phone frame holder was too short for my large phone with case. It is a Note 10. Frame was extended 15mm on the thread side. The channel around where the ball screws in was flattened to remove the need for supports in that area (Speeds...

The original phone frame holder was too short for my large phone with case. It is a Note 10. Frame was extended 15mm on the thread side. The channel around where the ball screws in was flattened to remove the need for supports in that area (Speeds...

Slot-in [Stereo IR 170 Evaluation Kit](https://www.ultraleap.com/product/stereo-ir-170) mount for use on tripod or use with other #1/4-20 fasteners. Unlike the [above screen SIR170 mount](https://www.thingiverse.com/thing:4821694/files) this mount...

... the best possible outcome, do not forget to share your printed product. I replaced the previous version's M6 nut with a 1/4 inch nut, which is the standard size for tripods. ...Additionally, I improved the slot's tolerance and depth for the hex nut.

A filament-efficient tripod that is quite small and easy to fold to nearly flat. My goal for it was to help film my golf swing to analyse areas of improvement. It works well to place on uneven surfaces. I designed it with galaxy S8 in mind, but it...

This is a phone holder!

Telephone Attachment System for Telescopic Stand The telescopic foot is secured with a robust M6 bolt and nut, providing a sturdy foundation for your phone. Installation instructions are conveniently located in the middle of this video, making it...

This platform has been engineered to sit atop a tripod (specifically, my quick release system). A compact recess is located at the bottom of the structure to secure it to the camera mount. Carefully screw it into place for the initial assembly. The...

Most tripods used in the US typically utilize a 1/4-20 thread for mounting cameras. You'll also require two M3-10 screws and their corresponding hex nuts to secure the mount to the scanner. These screws merely hold the acrylic using pressure, so you...

Mount the slab securely onto this sturdy base by connecting it firmly. ...Tighten the screws tightly into your reliable photographic tripod, completing a compact outdoor-style table with ease.

Mount your GoPro on any tripod with a bolt in its center by using this adapter. If you face issues with the design from jpmurph, modify the STL file in Blender for better fit. The initial issue was a too-small and not recessed enough hex nut hole; it...

I built a custom case to house the three-cell battery that energizes my leftover seven-inch monitor from an old in-car DVD system. ...I plan to utilize it so others can view exactly what I'm observing through my Fatshark goggles.

It's very easy to modify if you need to. The clamp goes from 57 to around 90mm. It's 40mm wide. It will hold thick phones, or a phone with a thick case. 15mm is around the limit. Depends on the shape. All parts are printed 100% solid. Parts are...

You may need to change the screw that attaches the tripod mount to the iGuide because of the thickness of the mount will not give you enough threads into the iGuide system. You can use any bubble level smaller than the 1 3/8 bubble listed below:...

In contrast, the "Iphone5tripod.stl" model is designed for phones sized between 59mm and 64mm, such as the iPhone 4, 5, 5S, or SE. It's essential to measure your phone if it has a case. The tripod's performance was only thoroughly tested with an...

... Creative Cell Phone Stand is compatible with all 4 - 6 inch cellphones. It provides stable holding and comfortable viewing for reading, making FaceTime calls, surfing the web or watching movies. Adds 10 decibels of volume to your Phone's speaker.

Instructions: Breaking down this flip phone into its individual components required some patience, but ultimately proved well worth the effort! You see, you'll need an exacto knife and a screwdriver - make sure you unplug that screen before...

For a fast solution, I simply created a webcam holder that attaches to my tripod. I used ABS for printing, ensuring a 5mm brim and honeycomb support. ...The hole requires tapping to fit a 1/4-20 screw.

A quick replacement if you mislay the camera mounting plate for your tripod. I've tried to use internal features for re-enforcement, adjust number of perimeters and layers so that the screw location has no infill and the retaining clip face is also...

However, it was essential that this universal mount fitted perfectly on a tripod with ¼ inch Kodak thread. That's why I reworked the original to meet my requirements: - The ball joint was removed. - A guide for the rubbers was filled in. - A web...

This tripod mount for machine gun is a high-quality, photo-real model. The model accurately represents the real world in terms of size and scale. Ready to Render. An HDRI map is included. A high-quality model suitable for TurboSmooth has been...

This model was designed in OnShapeAll parts sliced with PrusaSlicer0.20mm layer height with 0.4mm nozzle15% cubic infillPrint 2x strap pieces in TPUPrint bracket in PLATo Assemble: - 4x M3 brass inserts to attach the TPU parts. - A standard camera...

just a longer arm to allow for cases

Fun project to allow me to use my Iphone for videos. ... Video link https://youtu.be/19-StMWldgU

As such, I also include a remix of the Universal Cell Phone Camera Tripod Mount by T_om. In my remix, I slot the mount to again fit a Galaxy S8 Plus phone with an OtterBox Defender case. I also rounded and angled some corners to use less filament and...

I genuinely adore this phone - it sparks fascinating conversations and earns me plenty of attention when I'm out in public. ...I take great pleasure in introducing others to the boundless potential of 3D printing, showcasing its incredible capabilities.

Then, use my custom OpenSCAD script to modify the file by removing scanner-specific parts and adding a thicker base with space for a standard tripod 1/4"-20 hex nut and bolt. The project is licensed under GPL, based on abarry's MakerScanner license...