tripod mount 3d print

I needed a smartphone mount for my tripod, so I designed this from scratch using Fusion 360. I know cheaper alternatives exist in the market, but learning the process was crucial to me. ... Here's a video showing you the design, printing results, and...

Galaxy S4 Tripod Mount Design Settings Print Printer: Velleman K8200 Rafts Unnecessary Supports Ignored Resolution Set to 0.02 Infill Fully Solid at 100% Notes on Assembly: Design enables use of either a 1/4" x 3/4" hex bolt or a 6MM x 20MM hex bolt...

This StickPic redesign (http://www.thestickpic.com/) features a tripod mount on a walking stick's end, ideal for self-portraits. Assemble it with a 1/4"-20tpi bolt, and optionally print a thumb nut for easier camera orientation adjustment:...

This phone mount is inspired by the Universal tripod phone mount designed by neyfrota, however I designed the model from scratch in OpenSCAD with the aim to make it more versatile and stronger. Mount it on a tripod, place it on a table or hang it on...

My suggestion is to print the two clips, plate and mount out of ABS plastic and then using acetone, glue the four parts together. They should snap fit quite tightly but the acetone will firmly weld the parts into a single unit. ...I don't recommend PLA...

This clever design takes full advantage of the 028B's tapered, twin shanked leg - allowing you to easily snap on printed tripod clips, then slide the assembly up the leg until it locks into a snug connection.\r\n\r\nIf you like this build, I've...

This is a mount that I designed because I wanted a reliable tripod mount with some additional features that were missing in my previous setup. A battery shelf for mounting the ground station and tripods, and it fits batteries such as this 1800mAh...

This is a precision-engineered tripod mount specifically designed for the ImmersionRC Uno 5.8GHz receiver. ... It securely fits on tripods boasting a 31.8mm base, leveraging the convenience of a quick release system.

Upgraded Design for Speedy777's iPad Teleprompter Tripod Mount - The Initial Version Was Too Compact for My Velbon Tripod, So I Expanded It Widthwise and Smoothened Out the Corners to Perfectly Match My Existing Setup.

Mohit Bhoite's Neopixel Lightbar Gets a Custom Tripod Mount - A Design Made Specifically for It. ...To Achieve This, I Created a Dedicated Clamp That Allows the Lightbar to Sit Securely on Any Standard Tripod.

This is a sturdy tripod mount designed specifically for securing a dartboard in place. To ensure a precise fit, the tripod's outer diameter must be approximately 35.2 millimeters. The holder features a press-fit design, which requires an inner...

The Samsung Galaxy S4 mobile phone can be securely mounted using both horizontal and vertical tripod mounts, providing greater flexibility for photography or video recording.

I needed something to mount my HDZero Video Receiver to a cheap tripod I already owned. ...Has the 3 pronged GoPro mount.

This is the mount used to secure a GoPro video camera to a standard tripod mount (really just a 1/4 -20 threaded insert, but whatever!)

I recently ordered a new 3 suction cup mount for my GoPro, but unfortunately the tripod mount that came with it was defective. So I decided to design a replacement and print it out myself. Here's what I got. ... Print Settings Printer Brand: MakerBot...

A clip mount with a female 3/8 thread that allows mounting your GoPro7 to a 1/4 tripod, with a reducer bush. It holds the gopro very snugly, so you might have to experiment with normals compensation in your slicer to get a good fit. Images show...

Insta-tripod and monopod ==================== Make sure to read **instructions.pdf** --------------------- It's a really portable and compact tripod or monopod, depending on your needs, which you can assemble in a fraction of a second. It's available...

This is a mount for the newer cylindical PSVR camera to allow you to mount it on a tripod or other similar mount. It has a printed 1/4-20 thread in the bottom for mounting, and a cradle on top for the camera itself. I use it with some cheap...

... files are available. I wrote a small blog post about this project here: https://todbot.com/blog/2017/02/07/learning-fusion-360-via-3d-printed-iphone-tripod-mounts/ Print Settings Printer Duplicator 4s Rafts Doesn't Matter Supports No Resolution 0.2

The pink part snaps in and out of the yellow/orange part (See 4th photo) so that you can quickly put the phone on the mount and remove it without unthreading the tripod screw. Print instructionsI print this in PLA with 0.3mm layers, but thinner...

(In the design there is a hole for another M4 nut in the bottom part which is supposed to be glued in place and should serve as a mounting point if you dont have a standard tripod mounting nut like I had laying around) SUPPORTED PHONES: You can use...

(In the design there is a hole for another M4 nut in the bottom part which is supposed to be glued in place and should serve as a mounting point if you dont have a standard tripod mounting nut like I had laying around) SUPPORTED PHONES: You can use...

It can for instance be found via: https://www.valostore.se/produkt/ficklampsfaste_korsad_universal/?ps if you for some reason want to buy it separately rather than 3d-print this piece. If you want to 3d-print it instead you need to buy the adjustable...

... ...The objective lens will be secured with a steel band ring mount and attached to a tripod or a photo EQ mount like the Star Adventurer Mini using an Arca Swiss mount adapter. All parts are printed and tested, functioning as intended for me so far.

After printing, it requires a nut compatible with the camera tripod format, which apparently measures 1/4-20. However, I couldn't verify this since I found the nut I'm using in an old crate of nuts. The Ricorée Antenna is a DIY project to build a...

This is an easy-to-assemble smartphone tripod mount that should be compatible with most devices. Here are the steps to follow: print out the required parts, heat up an M8 bolt, insert it into the turn wheel for a snug fit, cool it down by adding...

This is a simple tripod mount using the apple MagSafe charger to hold your iPhone. Uses the standard ¼" 20tpi bolt that are on tripods.Included the scad file for easy modifications.  Thanks to Dan Kirshner - dan_kirshner@yahoo.com for his useful...

Yes, another tripod phone mount. I've got an unorthodox clamp+ballhead setup that needs a compact phone holder, so I decided to design my own. Simple, slim, and adjustable - this is what I aimed for. Standard "tripod screw" ensures it can be...

... iPad Air 2 with a full smart case. The maximum thickness is 11.5mm. The tripod mounting plate attaches with a 1/4-20 screw and hex nut. ... I printed this with supports and used PETG because I plan to keep this in my car and didn't want it to warp.

This is a small but clever adapter I designed to mount two IKEA Frekvens, or rather, their LED Matrixes on a tripod. This adapter replaces one of the included connectors and allows you to screw it onto standard 1/4" threads commonly found on tripods...