tripod leg 3d models
58217 3d models found related to tripod leg.thingiverse
I design this to repair a damaged tripod.The brand is unknownI make with ASA.
grabcad
The school assignment involved fabricating a miniature tripod leg connector, which I designed as the initial prototype.
thingiverse
I shoot video from above view angle. ...Use this clamp on 19mm tripod leg to connect a selfie stick with gopro mount. Very useful in windy weather. ...Easy to use.
thingiverse
This is a quick and dirty replacement for my 3 broken oval shaped tripod leg clamps (see in picture). ... Nothing with much construction in CAD but for me it works fine :).
thingiverse
... USE V3 it has the BEST fit of all uploaded. V3 has a slightly larger hole, making it easier to fit onto the tripod leg. 123d file is provided as well (can use for tutorial). ... 123d Tutorial for 2d to 3d creation: http://imgur.com/a/z4QVO
thingiverse
... in ABS to use with a triangular piece of fabric. This then clips to the tripod legs to make a simple sling to hold my lens cap, light meter, and shutter release. ...Caution do not use it to hold a camera, lens or anything else that might break.
thingiverse
This small little attachment is designed to stay on one leg, then clip/unclip from the other to keep the tripod legs from folding open during transport. Most professional tripods come with some type of latch like this, but they inevitably break and...
thingiverse
This is a replacement for the clamp that is used to adjust tripod leg sections. Mine broke years ago, I had it welded (which lasted a little while) and I've been making due with masking tape Enter my DaVinci printer: I designed a replacement with...
thingiverse
This is a replacement tripod leg fastener I made to replace the one I broke on the tripod that came with my ring light. This is sized for the middle fastener (pictured) but all three looks to be the same design in different sizes, so this should...
myminifactory
This is a replacement tripod leg fastener I made to replace the one I broke on the tripod that came with my ring light. This is sized for the middle fastener (pictured) but all three looks to be the same design in different sizes, so this should...
thingiverse
Slik 523QF Tripod Leg Clamp and friction block. This is the bigger clamp that usualy brakes (Tube OD is 26,65mm). This is my own drawing and requires the use of the custom friction block included. If you use the original friction block, it will...
thingiverse
Slik 523QF Tripod Leg Clamp and friction block. This is the bigger clamp that usualy brakes (Tube OD is 26,65mm). This is my own drawing and requires the use of the custom friction block included. If you use the original friction block, it will...
thingiverse
I designed a 2-stage leg for the Compact Phone Tripod (https://www.thingiverse.com/thing:2975272).
thingiverse
... This object will help keep the legs together and still be easy to open the legs when I stop to observe. This fits my Induro GTT204 tripod. It may also fit other tripods whose center column and upper leg sections measure approximately 28.5mm. ...
thingiverse
I made this remix of LKLyon clamps as the originals were too narrow for the leg spreaders on my 102GT tripod. ...I beefed up the leg clamps and opened them up to fit my spreaders
thingiverse
Caps suit the legs of a Slik Pro 500DX tripod which have a diameter of 27mm. Printed in Esun transparent yellow PETG. ... You can customise your own at...
thingiverse
If you have a Manfrotto tripod and you missed a leg hook, you can print a replacement Si tienes un trípode Manfrotto y perdiste el seguro de las patas puedes imprimir un repuesto
thingiverse
This is a holder for the 38mm legs on a Celestron tripod. It basically snaps on and keeps them from opening up during transport. I printed in PETG for strength and heat resistance, but you could probably do in PLA as well. I would use a...
thingiverse
This is a pair of replacement leg clamp bodies for the Focal 20-08-43 tripod. It is only the body of the clamp mechanism as non of the other parts are in tension, so they are much less likely to break. There are two different sizes as each segment...
thingiverse
Dress Mannequin Tripod attachment. Infill 60% or greater and walls at 1.2mm minimum. ... needs Structure
thingiverse
Libec TH-650, part that attaches the mid level spreader to leg. ...Please note that this model does not have the clip for locking legs together, using strap instead.
prusaprinters
Dress Mannequin Tripod attachment. Infill 60% or greater and walls at 1.2mm minimum. needs Structure Print Settings Printer Brand: Creality Printer: Ender 3 Resolution: 0.2 Infill: 60% Filament: Pantech PLA White How I Designed This...
thingiverse
Bracket to hold Skywatcher EQM-35 tripod legs apart and rigid for transport.
thingiverse
Tripod leg clamps for 1.125" legs. These are replacements I created for an older Celestron telescope tripod. These kinds of tripods with aluminum extrusion legs are fairly generic, so it may work for yours. ...Use two M4 screws along with the insert to...
prusaprinters
Tripod leg clamps for 1.125" legs. These are replacements I created for an older Celestron telescope tripod. These kinds of tripods with aluminum extrusion legs are fairly generic, so it may work for yours. ...Use two M4 screws along with the insert to...
thingiverse
... speaker stand tripod TLF162. ...Printed with PLA but probably better to print this using ABS. Uses 3 x 5/16" and 1 x 1/4" nuts If you don't want to print it, can be purchased here: https://www.pssl.com/products/ultimate-tlf162-tripod-leg-fitting
thingiverse
This is the leg's end tip for a Meade #844 Deluxe Tripod Leg. Mine cracked and Meade said they don't carry the part and wanted me to buy a new tripod. The original part has a rubber cover for the tip that will fit in this new part. I have placed...