triangle mask from squid game 3d models

This version prevents the lead-screw and bearing from rattling around while printing. [UPDATE6] Added POM nut adapters, 18mm hole spacing and 16mm hole spacing. This should allow you to skip buying the one I listed. [UPDATE7] Added x-idler v1.1.stl...

4 - When removing parts from the printer bed, it's a **VERY** good idea to place left/right parts into separate containers to help with the assembly process. Sometimes the difference between the left and right parts is very small but it is still...

I suggest you go for a "shifter_ram_ball_harder.stl" file instead of a regular one. About Thing This is v.1, it requires modifying prints with soldering iron to fit, don't print if you don't have to. v.2 is already in the making, I'm publishing this...

‘Tighten’ the knob (turn clockwise when viewing from underside) until you can slide your levelling sheet under the nozzle, then ‘loosen’ the knob until you feel a good deal of friction but can still easily move the sheet. Depending on the bed surface...

And if you like, share it with others!Model DetailsThe model is designed to match the dimensions and airflow mechanism from the original pods, so it will seal the pod when pushed down and open the airflow when in the upper position on the bottle. For...

Use thread locker on the M4 screw if you have some.Add a small piece of tape on each M4 nut to protect the pegboard from the screw.Install the M2.5 T-Nuts and screws.Install the mounts on the Skadis pegboard as shown below.Install the Waveshare Pico...

‘Tighten’ the knob (turn clockwise when viewing from underside) until you can slide your levelling sheet under the nozzle, then ‘loosen’ the knob until you feel a good deal of friction but can still easily move the sheet. Depending on the bed surface...

When you want to take the lid off again, use the hole to press a finger on the baseplate to separate it from the lid.Setups have made some setup combinations to get you started, and there will come more in the future. you can the replicate these...

Slip this printed part onto the two Y axis rods, placing the metal rod into the lower slot where it was removed from. Third, print the Z_stabalizer_Base and place it on the base of the printer so that it straddles the nub used for screwing in the...

This worked well and the screws from the original headset self-tap and holds the headset together nicely. The clip in the middle of the printed head strap that holds the padding seems to be slightly too wide. A bit of work with a file solved the...

It came with 1.75 mm filament, the same type used by my home printer, which meant I had an abundance of scraps from the Bowden tube and other leftovers. For about two hours, it was great fun, but when I owned a 3D printer, it became redundant and...

This version has slightly smaller cuts so it'll be tighter when placed on Part 2.4 - Button: Just a button.5 - Compression Spring: 3D Printed spring6 - Top Lid: Thin, flexible top lid to cover the mechanism and prevent it from coming apart.Mechanism...

If you have Fusion 360, then you can also export your design to .DXF and then import it to Estlcam. If you have any questions about this conversion, please let me know in the comments. Support If you want to support me for the designs I publish for...

I found something much better to shield the plate from the heat of the metal than just thin Kapton tape: silicone. I cut out a small piece of a silicone mat (actually folded it to have two layers) and put it underneath the mount plate. And voila - no...

If properly assembled with colors aligned as shown, _Starlight_ creates the appearance of triangular sticks running continuously through the length of the puzzle, although this is an illusion: the individual pieces are formed entirely from half-stick...

World War II Centaur tank, the last type to fit the Nuffield Liberty As World War II loomed, Nuffield, producing British cruiser tanks, licensed and re-engineered the Liberty for use in the A13 (produced as the Cruiser Mk III) and later cruiser...

The idea for this puzzle came from a similar one that Bill Cutler designed many years earlier. His looks like an ordinary six-piece burr except that each piece has a pair of additional diagonal notches. Half of those notches are unnecessary, and so...

squares and plazas
 railway network includes 2 objects : railway system (public transport) and stations
 – district borders and boundaries is 1 object (yellow in the preview images) UV mapped with overlapping UVs 
 no textures included /...

If it does, remove some material from the centre hole of the winding wheel until it spins freely. The winding wheel teeth should point downwards, and the indent in the top of the hub post in the opposite direction to the teeth.</li> <li>Insert the...

The flexible hose should be suspended overhead, centered on the work area and should have at least a 4 foot rise with ample slack so as not to place side loads on the tool anywhere within the work area. File Dust-Shoe-Mount.stl may be printed or cut...

The magnets I used in my case where Ø 5 x 1 mm.In the following GIF we can see the alignment and how the magnets keep the box open or shut:The plug model that this case accommodates has more or less the following general dimensions:Of course, since...

You just have to plan to separate them smoothly from one another. Provide A layer height that is thin enough for the holes in the hinges to be precise enough 3 or 4 lower and upper layers for finishing. 3 contour / perimeter shell for strength. 35%...

I purposely printed a full second set of the parts since they are easy to lose.Also, the eyelashes can break during installation, so having another pair handy will make the assembly go smoother.4 - When removing parts from the printer bed, it's a...

Update : 16.06.2022 First Pictures from the Shredder. I modified some Parts and will upload them later. Update : 17.06.2022 Most of the Prints are updatet. Changed the Guides so that the Shaft could be removed in one peace. ... Update : 22.06.2022...

These are 4 different kazoo holders that I designed to keep the mouthpiece from getting dirty during travel or so you don't have to lay it down on a dirty surface. it's a nice little stand to slide a kazoo in for storage. let's say you want to bring...

8 20cm wires F to M for LCD to Arduino 3 20cm wires F to M for DHT22 start from Arduino 3 10cm M to M intermediate (for resistor) 3 20cm F to F connecting to DHT22 Print Settings Printer: QIDI Tech Rafts: No Supports: Yes Resolution: 0.12 Infill: 30%...

Range: A temperate native with a very wide area, from Africa to Asia and Europe. Notes: Since World War I, this plant has become a symbol for fallen soldiers, often used in various remembrance ceremonies. It is also used at ceremonies for Anzac Day...

I also removed text from the back panels as they didn't print right.\r\n\r\n- - - \r\n\r\nUpdate: 5/20/2019\r\n\r\nI added narrow side plates, made the parts of MKS and RPi 4-4 that mount to the front of the frame thinner, and adjusted alignment some...

Its power supply can range from 4V to 24V, although the most commonly used voltage is 5V. A drawing is also included with the timing results for a burst of 5 balls. It's essential to note that sometimes the speed can be quite high (pulses about 25...

If you wonder why red, yellow and black, it's not because the clock I got inspired by used the same color, it's because we are from Belgium and supporting for the EUFA Euro 2020 :-)Instead of 3 colors you could do 2 colors as well, one for the body...