trekking pole clamp 3d models

The pin in the default model is 4mm in diameter and the model "Flat" can be edited for whatewer purpose is needed. The Thumb Nut hat 2 options - for thread tapping or for M3 Nut. For the M3 Nut the print must be paused on the 6.4mm mark and the M3...

<p>The pin in the default model is 4mm in diameter and the model "Flat" can be edited for whatewer purpose is needed.</p><p><br>The Thumb Nut hat 2 options - for thread tapping or for M3 Nut. ...For the M3 Nut the print must be paused on the 6.4mm mark...

This stand is specifically designed to support Black Diamond Expedition poles.\r\n\r\nThe included screw can be threaded into either a 1/4" or 3/8" opening, as seen on the link here:...

Rubber buffer for trekking poles made of TPU

I designed a versatile clamp and clip attachment specifically for camping poles, intended as a backup solution in case of adapter loss or when adapting poles for alternative uses.

Can be printed without support. ...Uses a 6x25 fastener for the pole clamp and reuses the hardware from the fan for the other side.

Enjoy landscape photography but don’t want to carry a heavy tripod?This compact clip system turns a pair of trekking poles and a monopod into a large tripod in seconds.Small and light enough to slip into your pack, it is secure enough to handle a...

This DIY project involves integrating a GPS mount into a 36mm pipe clamp, providing a versatile solution that can be easily adapted to fit different diameter poles. The design caters specifically to scientific fieldwork where the simultaneous use of...

These are simple anchors that snap onto the poles of your grow tent for clamping small fans to. These snap fit onto 16mm poles. There are a few version, I was playing around with the shape optimization in Fusion 360. ...The one named clampvertallfinal...

This cable clamp is specifically designed for use on poles measuring 1.375 inches in diameter, so be sure to take note of that crucial dimension. It will not fit standard t-bars, which are typically only 1.125 inches wide. ...This particular clamp is...

ANTENNA CLAMP

I got two geocache concepts mixed up. ...The pole part is actually a clamp for 60-61 cm road signs with a 70mm tall screw-on container. ...There's plenty of room to fit a rolled-up log, pencil, and even a small trackable item inside.

This clamp secures firmly onto the vertical pole of a dog agility jump, holding the horizontal pole in place. A deliberate design choice makes the supporting part extremely shallow, ensuring it falls easily if the dog bumps into it, preventing...

I saw the clamp by rainb0w_wheez3 at https://www.printables.com/model/20305-intel-nuc-pole-mount whic had the perfect mount for my Arlec LED floodlight that I wanted to attach to my camera pole.  problem is it fits a 35mm pole and mine is 15mm.  it...

While the nubs are strong enough to hold the weight of the basket plus another 30-40 ibs (depending on your print settings and material), there are four holes drilled into the corners so you can slide a screw and nut into the clamps to help ease the...

Use a coin to tighten it.Put the three main pieces together as shown in the pictures.Use the longer bolt to secure the pieces to each other and clamp them to the pole.Insert the second nut in to the space for it that is in area where branches are...

A trekking bottle, created through modelling in NX 7.5 software, has been rendered to perfection using the same program's rendering capabilities.

Sony PX470 Voice Recorder Case and Pole Mound for Insta360 poles 24mm and 31mm 24mm is for the standard insta360 invisible stick. ... 31mm is for the insta360 invisible tripod stick.

... grow tent's poles. ...These snap-on attachments fit perfectly onto 16mm poles and come in a few variations. ...I experimented with shape optimization using Fusion 360, and the clampvertallfinal design appears to be the strongest and most secure option.

To achieve this, create a simple clamp that can be printed using elastic filaments like ASA or ABS. This will provide the necessary flexibility and durability for the clamp. When adding or removing the clamp, exercise caution to avoid damaging the...

Sony PX470 Voice Recorder Case and Pole Mound for Insta360 poles 24mm and 31mm 24mm is for the standard insta360 invisible stick. 31mm is for the insta360 invisible tripod stick. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No...

Simple clamp to fix the tarpaulin on INTEX pools.This should avoid the tarpaulin to be blown away on windy days.I recommend to print this with somehow elastic filaments like ASA or ABS.To keep the camp flexible i also recommend to print it without...

They clip onto 22 or 21mm main spars using two clamps at each end. Commercially purchased ones often fail the job, so I designed these alternatives to replace them. The updated version now includes heavy-duty versions with wider mouths for easier...

Customizing options include gopro_secondary_rotated = 0, gopro_bar_screw_head_d = 6.2, gopro_secondary_what = clamp, gopro_bar_screw_shoulder_th = 4.5, gopro_bar_screw_nut_d = 6.01, gopro_captive_rod_angle = 45, gopro_bar_screw_d = 3, gopro_bar_gap =...

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=119508 Instructions Using the following settings: dsz = 1.7 dsy = 1 dsx = 3.5 cz = 1.7 cy = 0.9 cx = -8 sz = 1.2 sy = 1 sx = 4 dzalpha =...

Can be printed without support. ...Uses a 6x25-30 fastener for the pole clamp and reuses the hardware from the fan for the other side.

I placed the original design on my hiking pole but had the basket separate from the post due to a design flaw that allowed for a millimeter gap between the support bars and center post. In order to address the issue, I closed the gap and added a...