trekking pole clamp 3d models

Options used: screw hole diameter: 0.25 inches clamp height: 1.18 inches resolution: Fine screw recess diameter: 0.354 inches nut type: Nylon with rubber insert Press "Make it!" to download and print this customized object or explore more...

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_secondary_what = clamp gopro_bar_th = 3.2 gopro_captive_rod_id = 3.8 gopro_bar_rod_d = 12 gopro_primary = triple gopro_bar_screw_shoulder_th...

... radius and 70mm height, can be scaled in one direction or all. Simple to print, can be printed without support or with organic one for better inner quality. Prevents poles tearing other things during transport and leaving dust / mud from trekking.

This is a double-sided clamp for a monitor pole (33mm diameter pole). Its not pretty, I'm not a designer by trade but it works to add a pole extension to your existing monitor pole for a light monitor. (I would NOT use a full sized monitor with this...

I designed this simple clamp that attaches to a 24mm diameter pole with a single screw and nut. The screw goes through one side of the clamp, then through the eyelet of the flag, then through the other side of the clamp and tightened with a nut. ... ...

Tappo dimensioni 28mm x diametro interno 10mm Si consiglia la stampa in TPU con riempimento 100% Cap size 28mm x inner diameter 10mm TPU printing with 100% filling is recommended

... I used 80% infill for strength. I tried this print with black PLA and you can tighten the pole quite hard. Stress tested one that broke in the middle after really tightening it too hard. ...Will also try this print in ABS and see if it is stronger.

Slide onto pole at 45 degrees and twist to clamp to pole, can be used in tents for example on a tent pole to hold torches etc

Simple replacement clip for nordic walking / trekking poles.

A clamp for attaching equipment to a round pole or pipe (or maybe for attaching a pipe to a wall). ...Pole size, clamp dimensions, and hole sizes are all customizable.

A clamp for attaching equipment to a round pole or pipe (or maybe for attaching a pipe to a wall). ...Pole size, clamp dimensions, and hole sizes are all customizable in OpenSCAD.

A clamp for attaching equipment to a round pole or pipe (or maybe for attaching a pipe to a wall). ...Pole size, clamp dimensions, and hole sizes are all customizable in OpenSCAD.

This two parts should be used on quick connection clamp to connect two poles together, one parallel to the other or perpendicular. ... I will post a picture ASAP.

I've build a clamp to hold my weather sensor shield at an antenna pole (43mm). This time I used wood screws / Spax to tight the clamp together. ...I'm not really satisfied with that try, but you can use countersunk head screws, that's better.

I've build a clamp to hold my weather sensor shield at an antenna pole (43mm). This time I used wood screws / Spax to tight the clamp together. ...I'm not really satisfied with that try, but you can use countersunk head screws, that's better.</p>

... for little birds. ...This clamp can be attached to such a pole (if too loose, add some paper or plastic sheets for tighter clamp). It provides a stable foundation for large plastic boxes (e.g. ...for cakes or veges) and stops squirrels climbing up.

The clamp is designed specifically for a stock pole, utilizing M4 bolts for secure fastening. A visible PNW CREW logo is the sole notable feature on this particular model. ...However, I didn't create this design, as it was provided to me some time ago.

Designed to clamp onto the lowest section of the pole stand. Feed the cable through the bottom and connect, the power supply should fit snug with the feet going into the cutouts. Tilt the power supply away from the pole to remove. ADDITIONAL HARDWARE...

I wanted to design something to hold a pole right near my picnic table and found [falconphysics' V-Groove Table Clamp](https://www.thingiverse.com/thing:2399418) to be the closed to what I had in mind. Remixed it a bit to suit my need: - Chopped...

I designed this 'Power Pole Pair Clamp' to replace the pin. It is printed with the center pin flat on the bed, which makes the pin stronger. The pin is also flattened on the bed side to increase strength and beveled on the end to ease insertion. ... ...

I'm passionate about hiking and capturing its beauty through photos and videos. Frequently, I bring my camera along, eager to freeze perfect moments. For a long time, I've wanted to have a monopod to stabilize my shots. When it comes to video, the...

Consider printing a model with thick walls and low infill (around 10-15%) for better strength. Drill a hole at the bottom, insert your desired handle, and fill it with PU resin. Alternatively, make the design hollow. ...Note that the provided .stl file...

I'm an avid hiker who loves capturing stunning moments on camera. Frequently, I bring my gear along and snap photos or record videos of the breathtaking scenery. For years, I've been eager to get my hands on a __monopod__. In video recording, it...

<h3>MOLLE clip for 20mm stick</h3> <p>The hole is 21mm, so it's not super tight, just for the stick staying in place.</p> <p>If you're confident with the strength of your print, you can try the thin one.</p> <p>If not, use the wider one! ...← Super...

Camera Mount Tripod Avid Users Will Adore. Here Are The Must-Haves: Essential Tripod Mounts Found at Amazon, Click This Link: https://www.amazon.com/gp/product/B00C3DY73S/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 Necessary 1/4" x 3/4" Bolt - Be...

Use a rubber band to hold your smartphone in place and prevent it from sliding around. Before printing, edit the dimensions of p3_smartphone to match your smartphone's size: 65.8mm wide and 8.4mm long is a good starting point, which fits perfectly on...

The MOLLE clip for a 20mm stick is designed with a hole that measures 21mm in diameter. This allows for a snug fit of the stick, yet still enables it to remain securely in place. If you're confident in the strength of your print, you may choose to...

This is a simple clamp suitable to ATL LTE in order to asjust pan and tilt

... Options Available for Use: nut_type = 12 (set default value is Socket Head Cap) clamp_height = Sixty (minimum ten, maximum three hundred forty, in increments of two point five millimeters) screw_hole_diam = Nine point five six (minumum 2mm, max.

And yes, it's entirely possible to create trekking poles using just a few dollars' worth of aluminum tubing and some rubber chair feet... plus a 3D printer! Read on for the reasoning behind the design and its features, or skip ahead to the printing...