treadmill with tablet holder 3d models

Made this for use at the gym where their treadmill's book/tablet holder is too low, so I needed something at the top of the control panel. Version 2 Printing screws horizontally makes them stronger in my opinion than printing vertically and they...

Their treadmill's book/tablet holder is too low. I needed something to be towards the top of control panel. Version 2 Screws are easier to print horizontally (stronger IMO than vertical print) and don't need much support. Two main stands are...

... ... This sturdy stand securely holds a tablet in place while also clamping firmly onto the top of a treadmill's control panel. ...By doing so, it enables users to optimize their viewing angle and height for an improved overall experience.

Don't use support for the small partsTwo files to print1-  Small parts (Print_Arranged_Small_Parts.stl / Print_Arranged_Small_Parts SHORT CLAMP)2- Stand (Print_Holder_Tablet_Phone.stl / Print_Holder_Tablet_Only.stl)I arranged the small parts so they...

I design custom tablet holders specifically engineered to securely attach to treadmill consoles, allowing you to seamlessly transition from exercise mode to reading or browsing mode while maintaining optimal comfort. ...This innovative accessory...

Frame to hold a laptop/tablet on your treadmill arms so you can work and exercise at the same time. Uses three pieces of aluminium available from your local hardware store, 25.4mm tube for the cross piece and two 40x20mm for the two other pieces.

... close to the panel so lager tablets could fit. The original plan was one wide piece but two smaller ones seem to work better. I suspect other Proform and Nordic-track treadmills use the same tablet holder so this might work for other devices. ...

I made this support for tablets from the Dream Fitness treadmill, best sold here in Brazil. Pay attention to the supports, because if they are placed on the thread it is very difficult to remove later Fiz esse suporte para tablets da esteira...

This a simple tablet holder for the FYC JK8801F Folding Treadmill. ...The area for devices is far too small for a tablet to sit in landscape view, so I created this that slots into the existing device holder.

The ProForm 580 treadmill comes with a tablet holder that doesn't obstruct airflow from the cooling fan. Made for tablets between 7" and 8", it can possibly work with a 10" tablet in an emergency situation. The back boasts numerous reinforcement...

The button heads are used to attach the brackets to the treadmill: - 4 metric socket flat head, stainless steel 18-8 (A-2), 4mm x 0.7mm x 25mm - 4 metric socket button head, stainless steel 18-8 (A-2), 4mm x 0.7mm x 25mm - 4 metric flat washers,...

Wanted a tablet at eye level for my 2020 Nordictrack 2950 treadmill (https://www.amazon.com/), so i made it in tinkercad. It snaps on to the small gap in the screen housing, and is sized just right for a Galaxy Tab S7. It also works on an ipad 10" -...

I wanted to use my old Nexus 10 on my treadmill, but the magnetic charger is stuck on the bottom of the tablet. ...I designed this panel to fix this issue.\r\n\r\nConsider showing your appreciation by tipping OldGaf and allowing them to continue sharing...

Design Process Designing this was quite straightforward Initially, I took the necessary measurements for both the treadmill machine and my tablet. With these dimensions in mind, I quickly came up with a suitable design in Sketchup and began...

This is a tablet or Microsoft Surface attachment for the Reebok treadmill.

... and move the models to fit your printer. I did not glue the arms in, they stay in place nicely with my print and allow me to change the width; you could easily glue them in place. ... The mounting holes are 5.5mm diameter and 21mm x 75mm spacing.

this tray is for the superfit treadmill if you print with plenty of infill it can support a 2 in 1 laptop be warned there are no guides on the sides to prevent sliding, but I find that things don't really slide, if for you they do I recommend adding...

this tray is for the superfit treadmill if you print with plenty of infill it can support a 2 in 1 laptop be warned there are no guides on the sides to prevent sliding, but I find that things don't really slide, if for you they do I recommend adding...

Phone holder for treadmill with four different positions. Print instructionsCategory: Sport & Outdoors Summary Phone holder for treadmill with four different positions.

A sleek tablet stand comes equipped with two convenient tray attachments, one situated on its front side and another on its rear side.

This charging stand can hold 3 tablets and a mobile phone, has space under it for a USB charging hub, and many holes to roll the cables and moreover to save filament.

Mount iPad Holder to Treadmill tube.

Mount iPad Holder to Treadmill tube.

Handy phone clip for joggers offers flexibility with adjustable hold for various strides and speeds on the running path.

This is a one-piece design for a tablet stand compatible with the NordicTrack T23.0 treadmill display unit only. It securely clips on to this specific display, positioning the tablet at eye-level when attached. What sets this design apart is that it...

wanted a tablet at eye level for my 2950 treadmill, so i made one. This clips on to the small gap on the top of the display. Fits a Samsung S7 tab, but should also work with a 10-11" ipad. Hope it works for you! ...Note you have to print 2 of these for...

Tablet stand with stylist holder

Top inserted holder designed specifically for the Google Pixel phone paired with a slim case. Printer Settings: Printer: MBot Grid II+ Raft Settings: Rafts: Yes Supports Rafts: Yes Print Resolution: Resolution: 0.3mm Layer Height: 0.3mm Infill...

Tired of struggling with tape, my wife requested that I create a custom iPad holder for her treadmill. The challenge was on! After weeks of refining the design, I'm thrilled to share it with you. This project took several weekends to complete, as...

This fits on the arm of my treadmill and has a divot+holes to run a cable tie through to hold it firmly in place (see photo). I feel like I should have cut this model in two for easy printing but I found that a bit difficult in Fusion. Instead I...