traxxas xrt wing mount 3d models

... is a GoPro housing and you can attach the camera. Additionally, I added a nut housing with wings for easy manual clamping for standard M6 nut which can be replaced with a ready wing nut. ...For assembly you will need also an additional M6x25 bolt.

Summary This custom mount securely attaches to the Wing Wing Z84 flying wing, specifically designed for its unique design. It hooks directly into the two small holes located beneath the Z84's fuselage. ...Printing with a 0.3mm layer thickness using PLA...

This is the crossbeam that supports the vehicle chassis of a vintage Traxxas Sledgehammer model. I believe this component should exhibit maximum strength when manufactured at an angle, just like its original design intends. ... To test its...

These two components form the essential part of the rear bumper attachment system in the Traxxas Slash, a highly versatile 1/10th scale four-wheel drive RC vehicle. ...I have carefully designed and incorporated an integrated hitch bracket onto the upper...

This is an evolution of the original Traxxas part for Slash. Fit the 4WD and maybe the 2WD. Made for 40mm height battery pack (max 14,5cm long). Ask me if you need an other height. This one is a lightweight version. Maybe not resistant...

The Traxxas Rustler ESC Holder is a clever accessory that securely fastens the Electronic Speed Controller (ESC), power switch, and capacitor in place. This convenient holder ensures everything stays organized and within easy reach during operation.

its an Gopro Mount for Rustler 4x4 !

These wings are meant to mount onto a Traxxas Rustler 2WD, although it can be used for the Stampede and Bandit but I've not verified that yet. These are designed to give your vehicle lots of downforce at high speeds for extra stability and ease of...

... arms integrated. No slide and lock just screw (M3) the arms on the mount. On this model I also made the screw holes (to connect mount to body) much longer to make it stronger. ...You can still use the same screws as before or use a longer screw.

This is a motor mount designed specifically for the Velineon VXL-3S system, featuring a durable 20mm fan to keep components cool and efficient.

... achieve optimal results, it's recommended to print supports at a 45-degree angle with 2mm spacing. 5/20/19: A V4 version of the mount has been introduced, featuring a strategically placed cutout for improved wiring organization and reduced clutter.

The E-Revo 2.0 wall mount securely holds the car in place, its retaining clip expertly pulling the vehicle firmly against the wall to prevent any potential roll-off caused by the car's substantial weight on the wheel mounts.

You will need an m5 nut(non-locking) and an m5 bolt although one is included in the stock mounting hardware for the GoPro Place the smaller part's base in hot water for a few minutes before placing it into the hole and you should get a perfect fit...

Mount the front battery support now! I've got a sweet 1500mah Lipo 3S ready to go. Share your thoughts and ideas in the comments below - looking forward to hearing from you! ...Cheers, Daniele.

Just a flat plate for mounting just about any ESC into the HCG slash chassis, I was able to fit a GoolRC 3s ESC off Ebay onto it without any issues.

The attachment point for the mount resides on the left-hand side of the framework, proximal to the fuel door location (please refer to accompanying photograph). An additional upper segment serves to extend the camera positioning, allowing it to be...

Once printed, simply press an M5 nut into the hexagonal recess (it should be quite a tight fit, so it doesn't fall out), then attach your gopro to the mount using the standard thumbscrew that comes with your gopro. This mount then simply clips onto...

A Front Bumper Mount Ring: An Improved Version This is an enhanced version of the original design found at https://www.thingiverse.com/thing:394116 (V1). ...The main goal was to create a ring that sits snugly and closer to the front bumper, preventing...

*Important - to do this mod you need to cut the two tabs off that slide into the stock servo mount. Once you do that there is no turning back as the stock servo mount will no longer work and the piece you are cutting is part of the axle. I just...

The Kyosho PRO-XRT 2WD buggy's transmission cover has the part numbers SST13 or SST-13.

Also check out my rear wing I remixed - https://www.thingiverse.com/thing:2563321 I designed a front wing to boost speed on my traxxas rustler, perfect for high-speed runs. This custom part generates substantial downforce at speeds above 45mph,...

This is a tool for removing the end caps of XRT Tactical solvent traps. ...It has text on the rear showing the direction to turn for loosening and tightening since it has left hand threads.

Measuring cup for XRT tactical 1" solvent traps. Now you can measure your recovered solvent! Nah, it's obviously a pin wrench. Fits both adapter and end cap. The pins are 1/8" x 3/8" stainless. Drive them in until they fully bottom out. ...

Traxxas T-Maxx 6S motor mount

Nitro Traxxas Revo Front Body Mount Replacement

Human mounts e-maxx on traxxas flux tork hpi.

Runcam 2 front mount for Traxxas X-MAXX

Traxxas Rustler 4x4 Rear Bumper Mount Part Number: 6737

Traxxas T-Maxx Classic 4S-6S Lipo mount

This is a Traxxas Telemetry Expander 2.0 mount, for mounting on the T-Bar of the Traxxas Sledge.