traxxas xrt wing mount 3d models

Wing Mounts For Traxxas XRT

New version of the wing mount, this is meant to be flexible but not crush the rear of the body.

XRT Wing Mount with Large holes

Hobbywing MAX6 mount for Traxxas XRT

this is a esc mount for the new traxxas xrt rc car that i made on fusion 360.

This plate allows you to mount a Hobbywing Max6 ESC in the same place as the stock XRT ESC. Requires 2 M3x8 and 2 M3x6 pan head screws and 1/8" acrylic or, if you want the plate to last longer than the chassis, Delrin. Make sure to round the edges...

v3 v1: 2x M3x25mm incl. ...spring washer & nuts + 2x M3x12mm incl. washer & nuts. v4 v1: approx. 4-5mm more clearance to the XRT roof skids (5mm longer srews)!

Use as battery tray for XRT Traxxas. Infill 25% or less. I prefer TPU but PLA or similar will too to. PLA may crack on impact on jumps. Space under the tray for the straps. Nut holes are 4,5mm deep so you can use self-locking nuts. ...

Reinforces the XRT's front bumpers a little. The 2nd file is wider at the hooks so it doesn't come out easily, but it's harder to get in. ... The holes on the sides are for those who want to attach them to the bumper.

Fits the Traxxas Sledge RC Truggy. TEST VIDEOyoutu.be/hIVh-Q1ImEU Aditional Hardware (Optional) This wing mount can be installed with the original hardware but it is recommended to use longer screws and lock nuts. ...Two 4x25mm screws  Two 4x35mm screws...

Easy to print spoiler with mount that fits some Traxxas vehicles like Rustler, Bandit, Stampede and Slash (4) 3x16mm screws to attach to rear shock tower (2) 3x10 mm button-head screws for spoilerNOTE: I used longer 30mm screws in the picture,...

Mount on left side front before bulkhead of XRT. One screw attached to receiver box. Print from TPU. ...

Mounting plate to install Max6 ESC in an XRT. Has a passage to run the wires for the motor fans or you can still use the stock fan wire mounting location. Includes file for optional power switch mounting bracket. ... Hardware: - (4) M3x 12mm to mount...

Currently Testing as a way to Hold a Battery in place in the XRT Between front shock mounts..

M3 x 10mm for the mount to the ESC M3 x 12mm for the mount to the chassis Use the screw removed from the stock ESC for the antenna mount

Ever wanted to attach a Traxxas Sledge wing to your Traxxas Slash 4x4 that you converted into a BackSlash? Well, you will now after printing my simple, bolt-on solution! I designed this part because I wasn't the happiest with just running bolts...

100% unbreakble tpu

I needed them so took out a day to draw/test/print. Now they work perfect and fit perfect. If anybody needs them too than here you go. I beefed it a bit up at the critical parts so they will not break easy. ...

Fixed wing mount for a variety of Traxxas vintage buggies (TRX-1, TRX-3, TCP).The standard wing mount on the TRX-1 was accomplished with buttons that held a wing wire to the shock tower. The TRX-3/TCP switched to a mount that is similar to the JRX2...

Refer to the accompanying photos for a step-by-step installation guide, showcasing how these parts seamlessly integrate onto the wing mount. The results are clearly visible in the photos, demonstrating the desired outcome after successful...

... requires: 62mm long 4mm steel bar and 2pc M4x25mm screws. ...The upper original screws are suitable for the lower mounting. You can print the entire wheel or rim and tire(must be TPU or softer)separately. ...The rim halves must be glued together.

This straightforward upgrade replaces the standard Traxxas Rustler body's wing with a new, identical one that utilizes the exact same 4mm fasteners as the factory installed part.

The wing insert for the new traxxas sledge. There is three different versions. ... You can use factory hardware no need to get new hardware

... It is also closed off under wing. V2 I fixed the tilting back issue and also lightened the wing up a bit. Adding a gap between the mounting bar and bottom of the wing as well as improving the countersinks for the screws. ...V2 is what is pictured.

This is a four-piece wing designed for the Traxxas (1:10) / scale Rustler 4X4. If placed diagonally on the print bed it will print on the Ender 3 and other printers of a similar size. For best results print the wing using PETG or CF-Nylon and the...

Spoiler wing for a Traxxas Latrax Teton. Mainly for aesthetic looks. Just need to line it up on the body, mark the holes, drill, and bolt on. I used standard M3 screws found on a lot of RCs, especially crawlers. If you liked the design, leave a...

Spoiler/wing to bolt onto the back of a Traxxas Rustler body. Just a quick design after ripping an old rear wing off. The picture is of V2. It does require different screws from the stock ones though. I had some 1/2 inch #8 machine screws laying...

This is a modified version of the wing system for traxxas rustler by Kyle bedrich. I built it to suit my needs in my road car build. ... Use wing 3.0, as it requires no support.

I got a brand new body for my Traxxas E Revo and the wing kept scraping against it, so I came up with this clever extension to lift the wing right out of the way. ... Just screw it in at the bottom using two M4 button head screws - the same type that...

A massive upgrade for the Traxxas Rustler 4x4/4x4 VXL - a more aggressive wing that's designed to withstand even the toughest crashes. I've given it a test run, but I'm still unsure of its durability. A higher infill and more forgiving material will...