traxxas trx4m servo 3d models

TRX4m stand and shock work stand. Made to be printed without supports and in one piece. I created different versions, this is still a work in progress as I continue to improve it. ...Please comment if there are changes you'd like to see.

Roof rack designed to fit a TRX4M Bronco. There are 2 racks included, a smaller one for the front and a larger one for the rear. You could use either one or both as I have. ...I attached them with 1.4x5mm self tapping screws.

Here are some mirrors for the trx4m high trail. They just snap together and into place. You'll have to punch out the OEM mirrors from the body. Do not damage the body, these are a direct fit. Some filing may be needed if the fit is a bit tight. Some...

Trx4m Arched Mod Chassis Rails. designed to fit 52mm up to 62mm shock length while increasing droop and flex while maintaining factory ride height. Fits both Bronco and Defender bodies. original front and rear bumpers will fit. most...

I wanted to lift the body on my TRX4M Defender to clear bigger tires and to allow for uninterrupted steering lock to lock at full compression. These prints replace the front and rear cross member / body mounts. Included is a rear High Clearance...

Here is my version of the suspension mounts for the awesome superscale 2k20 suspension system. ...I needed to mount the JSScale Discovery body which does not provide much space so I found a solution that does the trick.Enjoy!

100% infill suggested with whatever filament you like.

Currently Testing as a way to Hold a Battery in place in the XRT Between front shock mounts..

I crafted this on a whim but my inkjet is struggling to get it off the page. ... Could you give it a spin and provide some feedback?

You'll need to dismantle the current steering block and swap out the damaged arm with a new one fabricated from a 3D printed component.

wall mount traxxas trx4m remote and vehicle holder. fits vehicles from stock up to 70mm tires. ... 2 different top piece options(angled piece prints faster)

Interior for the TRX4M Bronco. The floor and trunk I made myself and is a prototype after I modified my original plan. It should fit pretty good. The floor is the only piece that needs support. The trunk is used on my Bronco which i chopped and...

Roofrack for the TRX4M. Use 4 spacers, place the rack on top and use a small ziptie to tie it to the rails on the roof. There are two kinds of spacers. A "detailed" one which has a shape that fits snug over the rails, they stay in place, making...

The battery holder can now hold bigger 2s/3s batteries while still using Traxxas' original rubber strap. Finally the Front Mount ESC clips into my battery holder and allows you move the esc/receiver to the front of the crawler for better weight...

With this flex blades for Traxxas TRX4-M the car will be 5 mm higher and the wheels can travel around 1-2 cm longer than original for greater performance. RR = Rear Right RL= Rear Left FL = Front Left FR = Front Right For assembly, four...

USING THE PRE MADE CONTROL ARMS YOU WILL HAVE TO CUT THE FRONT BODY MOUNT TO ALLOW ROOM FOR THE STEERING SERVO TO ARTICULATE SO I ADDED AN ADJUSTABLE FILE THAT YOU CAN OPEN AND ADJUST FOR YOUR PREFERED SETUP . JUST PUSHPULL THE FACE AND MIRROR JOIN.

TILT AVANT ET ARRIERE POUR TRX4M. ...L'AVANT EST MONTE PAR L'EXTERIEUR POUR GAGNER DE LAPLACE POUR LE MOUVEMENT DU SERVO. ... IL Y A UNE PLAQUE A VISSER 0 LL4ARRIERE POUR POSER L'ELECTRONIQUE;

Made to fit Traxxas Trx4m. Prints in 2 parts, cab and bed. Can use Cab Only or Full Body. I use 100% infill and print upside down for minimal support use. Cant wait to see what you do with this project.Don't forget to follow "Scaler Lab RC" on...

This is a spare tire delete for the 1/18th scale Traxxas TRX4M Bronco. The spare tire likes to hang up quite a bit so I decided to get rid of it. Very easy to install with the same hardware from the spare tire carrier. ...The recessed area is 9x18 for a...

Front and rear bumpers for the TRX4M Bronco.

TRX4M Beadlock Design, fits https://www.thingiverse.com/thing:5687206

Scaled down to fit in the roof basket of the TRX4M Defender

TRX4M with bumper. Looks pretty sick and does not really get in the way. Mounts on the original Bronco Chassis frame. ...No extra hardware

UAV Servo

servo motor

I didnt like the hole in the chassis from the reverse servo. ...I made this blank https://www.youtube.com/watch?v=Oa0Q6NcRk1w

Step one: Purchase trx4m trailer as well as spare trailer wheels and tires. Step two: remove wheels from trailer. Step three: install dual axle conversion using long screw that comes with spare tire set. Step four: install each wheel using the...

Rear ladder for the TRX4M Defender (1:18 scale) Prints well on its side without supports. Fix to the body with tiny screws - requires 1mm pilot holes to be drilled in body. I had to move the registration plate sticker to the correct location.

This is a big stinger bumper for the TRX4M Bronco. 3 M3x10mm screws needed to bolt together. Print at 100 for plenty of strength to lift the car itself. Might need to change the scale to times 10 for right size. bumper should be 28.726mm x 48.768mm x...

Hi,This is a remix of the wonderful ROP09's TRX4M trailer to use a hitch made with a M3 ball head screw like the Tamiya ones. ...The hole on the frame need to be tapped with a M3 tap and the ball joint is screwed with a headless M3 screw.The hole on the...