traxxas teton custom body 3d models

Front and rear LED lights holder kit for Traxxas TRX-4 Land Rover Defender body. There are .stl files for front, rear, left and right lights. You can choose with or without LEDs. Use original parts with my LED holders for better optical...

RC Body Clip Retainer/Tether Secures Body Clips, Fits Arrma and Traxxas Vehicles with Pre-Cut Holes. Drills a 3-3.5mm Hole Near Body Post Holes for RCs Without Pre-Cut Retainer Holes. This Print Does Not Require Supports Due to Double Cone Plug...

Summary fuel cap is designed to fit perfectly on the Traxxas TRX4 Defender D110 body. To print this model, set your settings as follows: Rafting is enabled for a strong and stable base. Supports are also included in case you need extra stability...

This bracket allows you to use the Traxxas clipless body mounting system (as used on the 2021 Bronco and other newer TRX-4s) on the older Bronco body. In addition to printing these parts, you will need the following Traxxas parts: 8080X (inner...

I designed this body for my brother's Traxxas Rustler. He thought the use of a 30's body would fit the chassis well. Being a 2wd version I thought that a 32 coupe hot rod would look good. He was right. It fits well. The cab is chopped and...

Quality and ready for print STL files. ...Wheelbase like Traxxas TRX 6x6 chassis 324 and 454 mm. Wide 245mm. ...Feel free to contact myrc4x4@yandex.ru

Front bumper replacement for LaTrax Teton.

The ultimate upgrade for your Traxxas TRX4 Defender D110 Body RC - a lift kit that takes your off-road adventures to new heights. This rugged accessory is designed specifically for the TRX4 Defender, allowing you to conquer even the most challenging...

... Cherokee body files for TRX4. ... Parts included: Rear hinge + body support Front part for clips (bumper not included) Seat base Wheel arches Superscale2K20 ESS Dual Support NOTE: Front bumper and dashboard/seats (available in Cults3D) not included.

Skid for the entire sledge body for non sledge car.I used it for an Hobao Hyper SSTE.

After letting a young man drive the emaxx and having him wreck it and pull the body pins through the body on both rear posts I decided I needed to disperse the point of impact that the pins have on the body. I've personally also ordered foam discs...

 :DImportant is, this kit will not fit on the original X-Maxx body, it's designed to fit on the aftermarket body made by TMS, because the mounting points of the inner frame are at a different location on the TMS body as on the original one. ...You can...

... to liberate their TRX4 from its stock fenders can now enjoy unparalleled space and versatility by removing them altogether. ...This modification unlocks a world of possibilities for mounting shocks, bodies, and even front battery trays with ease.

The body post screw assembly is centered around the proline Extended Front/Rear Body Mounts Slash 4X4, but they are engineered as alternatives to using pins. To download this upgrade, four 3x30mm screws and four 3mm stop nuts will be required. ...The...

I'll likely end up beefing up the ends, but I wanted to try them as slender as possible initially to avoid interfering with the body clips. There is one for the front posts, 71mm wide. And another one for the rear posts, 80mm wide. I also included...

They simply sit atop the original mounts and you insert body pins to secure them in place. All that's needed is a few m4 screws and matching nuts (possibly some superglue if the nut isn't tightened securely). First, I had to trim the screws to the...

... I inserted the nuts into the mount screws and also applied some superglue. (It can be a bit tricky to get the body pins in place at first, but after a few attempts you'll get the hang of it.) Feel free to share your thoughts on this modification.

Latrax Teton 1/18 Scale R/C Car Control Arm - A Simple yet Effective Design.

Model of Grand Teton in Wyoming with a 4"x4" base.

People often prefer to utilize a holder designed specifically for Li-po batteries when using their Teton. ...Alternatively, you can easily make use of standard batteries as well.

Gravity Research Center at Grand Teton Expands Its Capabilities - As Part of a Major Upgrades Program, Scientists Are Boosting the Shell Thickness to a Critical Level

Grand Teton Mountain Range from Idaho's Side Key Rack Letters are cut to accept key ring Two keyholes in the back to accept wall mounting hardware

The order has been placed for a 3D print of Grand Teton, standing tall at an impressive 13,775 feet (4,199 m), making it the highest point in the Teton Range and the second-highest peak in Wyoming after Gannett Peak. Situated entirely within the...

Our customized versions bear our names, and I'd be more than happy to share the file with anyone named Mike or Kim if they're interested. This particular roof rack was printed on our trusty Creality 10s. The hardware used in its construction is...

Simple stand for the Teton's, may work for the Pre-Runner and rally too. I printed mine with 30 infill which seems a little much. ... Stand has small parts holder and will rotate in itself as well.

... to Change Any Dimension Easily at Will. They're Much Tougher to Put on Than Regular Tires, so You'll Need to Use Tools Like Screwdrivers or Something to Get the Job Done Right. Update: I Redesigned My Teton Tires in OpenSCAD with Default Settings.

For the Latrax Teton bumpers, you can attach 3mm LEDs via the provided holes; however, no LED holders are included. To resolve this issue, I designed special brackets to securely hold these LEDs. ...Additionally, the front buckets have been modified to...

I was looking for an off-road wheel that's compact yet fiercely capable, perfect for tackling snowy or sandy terrain.

Customized version of https://www.thingiverse.com/thing:3655519 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3655519

Custom Body for Dicodes Dani Box Mini