traxxas t maxx models

designed this as a extra accessory for my traxxas UDR intended to be mounted on the rear bumper, or in location above were drive shaft is. Held in rear bumper by 2 screws 10mm length or under. or zip tie onto cage of udr. ...Can be scaled up and down...

GTR shock spring retainer for Traxxas #7561 and #7462 Print setting:Filament: PETG is recommended but PLA is workableInfill: Gyroid, 15%Enclosure: Not required Please let me know if there's any question in the comment section to help me improve the...

Traxxas Rustler Receiver Box Unboxed and Ready to Roll Out Inside the Traxxas Rustler Receiver Box, you'll find a treasure trove of high-quality components that bring this rugged off-road truck to life. The first thing you'll notice is the sturdy...

The bar with and without the flat panel is the VTx antenna mount, one version just holds a bulkhead SMA connector, while the other also holds a standard 30x30 PDB to make wiring FPV and other things simple (Outdated with the use of the Traxxas Light...

... to various design requirements. ...These advanced models incorporate state-of-the-art technology and improved features for a seamless user experience. ...With Creo 2.0, users can now effortlessly create intricate designs with precision and efficiency.

I recently broke the plastic spur gears on my Traxxas 2075 servo, which prompted me to design my own replacement. You may need to carefully file the center holes slightly to ensure a smooth fit, but so far, mine is working efficiently. ... Keep in mind...

Thumb Control for Traxxas Radios is Now Complete. A First Version Has Been Achieved Despite Some Minor Flaws. The Knob Is Slightly Off and Short, But It Gets the Job Done. Further Improvements Are Planned To Enhance Visual Appeal. 7/14/20 Update:...

I purchased an extremely worn Older Traxxas Stampede. It initially featured a mechanical speed control system. The previous owner had upgraded it at some point to a high-performance ESC, yet he merely used zip ties to secure it in place. I found this...

A 50-tooth spur gear for a Traxxas RC car is available with updated instructions. Version 1.2 features a solid side, while version 1.3 adjusts the holes for improved slipper fitment. The v1.4 upgrade increases bearing hole diameter by 0.5mm, and v1.5...

This is a four-piece wing designed for the Traxxas (1:10) / scale Rustler 4X4. If placed diagonally on the print bed it will print on the Ender 3 and other printers of a similar size. For best results print the wing using PETG or CF-Nylon and the...

Charge Indicator for Traxxas Connectors: A DIY Masterpiece Inspired by Canomod Project. This ingenious creation, crafted from scratch, boasts a smaller design while maintaining the same connector shape as its predecessor. Its strongest feature lies...

This is the updated design for the 1/10 scale 4x4 Traxxas Slash's A-Arm. It features standard mounting holes in the front for shock installation, as well as additional holes at the rear to accommodate a secondary shock mounted using my printable...

I'm overhauling a Traxxas Nitro Hawk. Having all the original components is a blessing, but I'm eager to test drive it without risking damage to those hard-to-find originals. To achieve this, I've decided to start fabricating replacement parts...

EDITED VERSION, FRESH DESIGNS INCLUDED Updated designs come with a reinforced bumper arm now available in 1/10 scale traxxas slash format. Two strategically positioned holes run through the center of this robust part allowing for an extra stabilizing...

Replacement tie rod for the Traxxas Rustler 4x4 requires precise installation, often necessitating reaming of holes with a 13/64 drill to accommodate factory-measured .200" / 5.08mm diameters. Experiencing part detachment from the build surface led...

This is for relocating the radio receiver in the Traxxas X-Maxx to mount the Hobbywing Max5 in-between the rails for lower center of gravity and without modifications to the chassis. I modeled the ESC plate as a template, should probably use an...

Designed specifically for my son's Traxxas Rustler 4x4 VXL, this setup should also work for other Traxxas vehicles that utilize TRA6845, including: Rustler 4x4 Rustler 4x4 VXL Slash 4X4 Platinum Slash 4X4 Ultimate Slash 4X4 VXL Slash 4X4 Stampede...

I needed a battery cover for my traxxas remote control transmitter after losing mine. I didnt have the original to copy so dont expect the tabs to be perfect !I am not sure I would declare it as complete but its good enough so I wont be doing any...

I designed a sleek new bumper for the Traxxas TRX4 that packs all the features of the original but in a more compact form. This custom bumper allows you to install four bright 5mm LEDs, giving your vehicle a unique and eye-catching appearance. What's...

This is a Shifter "gear" for the 1/10 scale Traxxas Summit. it is designed to eliminate the huge amount of slope in the original drivetrain. It should be a direct fit, but depending on your 3d printer it might need some filing. Here are my settings:...

This is a spacer specifically designed for Traxxas vehicles that fits snugly between the axle and wheel, ensuring seamless movement and precise handling in any scenario. I've had the pleasure of printing it using PLA material at an impressively fine...

This is a fully printable wheelie bar that fits RPM and Stock bumper mounts for Traxxas 1/10 scale 2wd Cars and Trucks including the Bandit, Rustler, Stampede and the Slash. I have printed it in PETG at 0.15 and 0.20 layer height at 6 sides and 70%...

I made this for my Traxxas Slash 4x4 but it should work fine for many other RC cars. This stand is adjustable with a minimum height of 140mm but can be extended to a height of 170mm+ but simply unscrewing the center bolt from the base. There is a...

Spoiler/wing to bolt onto the back of a Traxxas Rustler body. Just a quick design after ripping an old rear wing off. The picture is of V2. It does require different screws from the stock ones though. I had some 1/2 inch #8 machine screws laying...

Updated with New Design This A-Arm Works Perfectly for the 1/10 Scale 4x4 Traxxas Slash Vehicle. It Includes Normal Mounting Holes at the Front for the Shock Absorbers and Extra Holes at the Rear to Attach Another Shock Absorber. The Mounting Holes...

These supports were made to lift the front and back axel of a Traxxas Trx4 Defender RC truck for storage. I did not used the defender for a few months and the soft compound tires with extra weight in the rims had nice flat spots on them (more or less...

After hours of precision measurement and meticulous design, I created four test prints that led me to develop a brand new front bumper bar for the 1:10 scale Traxxas Slash 2wd. This custom part utilizes the original screws and mounting position,...

The maker then remade everything using a laser cutter and made it capable of handling Traxxas joints. A crucial reminder is that the stance between connections on the effector must match the carriage's stance for proper functioning. An update a year...

... link on a Stampede. Traxxas part number 3641A. This is PETG, and it held up great. I haven't tried PLA yet. I printed at 100% infill. This model was run on a custom Delta printer. No raft or supports were used. ...The resolution was set to .2mm.

I decided to fuse the two together and created an easy to build short wheelbase chassis for Traxxas parts. The wheelbase measures right around 210mm. The front bulkhead mounts the same and uses the stampede parts and geometry for steering. The rear...