traxxas summit body 3d models

Today I am adding another project, which is replacing the bodywork clips with nuts. ...Project made under Traxxas Summit.

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

I just wanted to try a different body on my Traxxas Summit. I also have a Traxxas Slash 2wd and made new bodymounts to make it fit. Summit with the Slash 2wd body. Think it look good. Have not yet tried to drive it, might break...? The tires might...

I just wanted to try a different body on my Traxxas Summit. I also have a Traxxas Slash 2wd and made new bodymounts to make it fit. Summit with the Slash 2wd body. Think it look good. Have not yet tried to drive it, might break...? The tires might...

TRAXXAS SUMMIT ROOF LIGHT for 5mm LED

Solid rims to prevent water from entering the tires Only for Traxxas Summit 1/8

Print Settings: Printer Brand: FlashForge Printer Model: Finder Rafting Required: No Supports Needed: Yes Resolution: 0.2mm Infill Percentage: 35-65% Overview and Background: The Traxxas Summit Mount is designed for the 1/10 scale Traxxas Summit...

Printed from Soft PLA. ...Protects the front upper control arms on the Traxxas Summit 1/10. ...Secures with zip tie to the lower control arm.

I enlarged the leg sections to fit the massive Traxxas Summit comfortably. Additionally, I drilled a few extra holes into the plate to minimize material usage. ...To achieve this, I printed it in PLA with a layer height of .2mm, and opted for a 15%...

This is a precision-crafted Shifter "gear" engineered specifically for the 1/10 scale Traxxas Summit. Designed to eradicate the colossal amount of slope inherent in the original drivetrain, this component is intended to provide a seamless fit. Here...

I designed this bottom plate as a cradle for utilizing a two-speed transmission from a Traxxas Summit in an Axial SCX10. This version is specifically tailored for use with the Axial OEM U-frame. Notably, the mount for the shifting servo requires some...

This is a Shifter "gear" for the 1/10 scale Traxxas Summit. it is designed to eliminate the huge amount of slope in the original drivetrain. It should be a direct fit, but depending on your 3d printer it might need some filing. Here are my settings:...

Just done a few more parts off the summit

I'm using this bottom plate, which I built to accommodate the two-speed transmission from a Traxxas Summit within an Axial SCX10 setup. The version of it shown is tailored for use with Axial's OEM U-frame design. I Made Adjustments: 16-07-08...

... I could drill holes into the rails and install screws to stiffen the rack even further. Lastly, four posts extended downwards from the body, allowing me to drill additional holes and utilize M3 hardware to provide extra support to the mount.

Here's a DIY FPV Base I Built for My TRX Summit - Any Help is Appreciated!

This is a lightbar for the Traxxas Summit. it is a direct bolt on to replace the stock 2 led lightbar on the front bumper. Designed it to be able to fit 6 pc of led to the bumper, so you can have a nice light bridge. With a regular design(6V BEC),...

This is a lightbar for the Traxxas Summit. it is a direct bolt on to replace the stock 2 led lightbar on the front bumper. Designed it to be able to fit 6 pc of led to the bumper, so you can have a nice light bridge.</p> <p>With a regular design(6V...

Some more on my summit... ...micro servo for transmission, and Front and rear T'lock (Diff lock...)

In the Tellusumm project, I constructed components for a Summit bumper which included a D-ring and a low profile light bar capable of accommodating seven 5mm LEDs. ...The D-ring is fastened using a 2mm screw, and there are plans to attach a small hoop...

TRAXXAS SUMMIT - wheel cap for 12mm scrue

stand for Traxxas Summit 1/10 0.220% no support

... a near-exact replica of the beadlock rings that come installed on the Traxxas Summit. ...These can be printed in any color to enhance the look of your traxxas summit, rather than painting the originals and risking the paint flake off after lots of use.

I recently acquired a high-quality FPV camera for my Traxxas Summit, but I knew I had to find a way to safely secure it to the vehicle while also protecting it from the rigors of off-road driving. To address this need, I designed and built a custom...

The 1/10 Traxxas Summit comes equipped with a robust rear brace designed to minimize rear flex during intense jumps and heavy landings. Constructed from high-quality ABS material, this durable component provides optimal support for your vehicle's...

This is a custom bottom plate designed specifically for using the two-speed transmission from a Traxxas Summit in an Axial SCX10. This version is optimized for use with a custom "flat" frame configuration. To accommodate this setup, I had to modify...

Utilizing a twospeed transmission expertly adapted from a Traxxas Summit, I have successfully modified an Axial SCX10 platform to provide optimal performance. For this model, the mount for the shifting servo needs to be slightly modified to...

... This cage is a remix of the Slash model, featuring a wider central section and a plate for attaching the camera, adjusted Side2 modules that fit the summit connectors, and a new design for the back connection.

I made this bracket to accommodate my Summit's FPV system battery. ... Width: 31.50mm Length: 110mm Height: 52mm

This is a versatile front stinger compatible with the standard summit bumper. Simply detach the chrome-finished light to make it fit seamlessly. ... For D-rings, check out this link: https://www.thingiverse.com/thing:165875