traxxas summit 1 10 3d models

This is a lightbar for the Traxxas Summit. it is a direct bolt on to replace the stock 2 led lightbar on the front bumper. Designed it to be able to fit 6 pc of led to the bumper, so you can have a nice light bridge.</p> <p>With a regular design(6V...

Some more on my summit... ...micro servo for transmission, and Front and rear T'lock (Diff lock...)

In the Tellusumm project, I constructed components for a Summit bumper which included a D-ring and a low profile light bar capable of accommodating seven 5mm LEDs. ...The D-ring is fastened using a 2mm screw, and there are plans to attach a small hoop...

To secure my GoPro firmly to the Summit, I required a more solid base. Fortunately, there were three effective ways to achieve this. Firstly, the rack could clip directly onto the rails for added stability. Alternatively, I could drill holes into the...

Scale up to a staggering 1,000% without hesitation or warning. ...No safety net or protection in place whatsoever, the wheel's pneumatic system and rim are left completely exposed and vulnerable to catastrophic damage.

TRAXXAS SUMMIT - wheel cap for 12mm scrue

The 1/10 Traxxas Summit comes equipped with a robust rear brace designed to minimize rear flex during intense jumps and heavy landings. Constructed from high-quality ABS material, this durable component provides optimal support for your vehicle's...

I recommend labeling this as suitable for both front and rear installation due to the common design feature in many 1/10 scale remote control Traxxas models, which often have longer hubs on the front two wheels compared to the rear. This versatile...

-> see MK4bDa ich kein Innenleben für das 1/10 Modell finden konnte, habe ich dieses für seinen großen Bruder angepasst. Es kann in die Karosserie eingehängt werden (fummelig, aber passt), keine Schrauben oder Kleber benötigt. Darunter bleibt...

... a near-exact replica of the beadlock rings that come installed on the Traxxas Summit. ...These can be printed in any color to enhance the look of your traxxas summit, rather than painting the originals and risking the paint flake off after lots of use.

I recently acquired a high-quality FPV camera for my Traxxas Summit, but I knew I had to find a way to safely secure it to the vehicle while also protecting it from the rigors of off-road driving. To address this need, I designed and built a custom...

Utilizing a twospeed transmission expertly adapted from a Traxxas Summit, I have successfully modified an Axial SCX10 platform to provide optimal performance. For this model, the mount for the shifting servo needs to be slightly modified to...

This is a custom bottom plate designed specifically for using the two-speed transmission from a Traxxas Summit in an Axial SCX10. This version is optimized for use with a custom "flat" frame configuration. To accommodate this setup, I had to modify...

I made this bracket to accommodate my Summit's FPV system battery. ... Width: 31.50mm Length: 110mm Height: 52mm

This is a versatile front stinger compatible with the standard summit bumper. Simply detach the chrome-finished light to make it fit seamlessly. ... For D-rings, check out this link: https://www.thingiverse.com/thing:165875

I created this modification to reduce the height of the 1/16 Traxxas front bumpers, making the Traxxas 1/16 E-Revo look even more impressive. If you decide to download and install this file, you will need two screws: three by fifteen millimeters and...

Traxxas replacement knuckles are specifically designed for the 1/16 series. These parts come separately as left and right knuckle assemblies. To complete one side of a vehicle, two knuckles (either left or right) are required along with four hold...

This micro camera mount perfectly fits the 1/10 Traxxas Summit, providing a secure yet easily removable platform for your camera setup.

I designed this part specifically for my 1/16 E-Revos Shocks, as I encountered a problem with the spring set I had ordered - the black springs were shorter in length than expected. This resulted in the need to adjust the spring all the way down,...

1/10 Scale Traxxas Slash Wheel. ...print at 100% infill with the concaved side upwards.

1/10 Scale Traxxas Slash Wheel. ...print at 100% infill with the concaved side upwards.

Надёжно удерживает корпус дифференциала от проворачивания при откручивании/закручивании винтов, а также удерживает дифференциал в вертикальном положении для заливки масла с последующей сборкой.Подходит для моделей Traxxas 1:10 4wd: Slash 4x4, Rustler...

Battery holder made for bigger batteries for Traxxas Slash 1:10 4x4, but it could fit for more models. I will appreciate, if you tell me, what models it fits. ... 4 versions: * 27mm * 28 mm * 29 mm * 30 mm

I built this stand for my son's Traxxas Rustler 2wd 1:10 scale so he can store it safely with wheels off the ground. I left the front of the stand open to create some useful space under the car, and our model battery charger (Traxxas EZ Peak Plus)...

The front axle was designed specifically for 1:10 scale Traxxas 2wd vehicles. To get it working, you'll need 11mm x 4mm bearings/bushings, which are also used on the Stampede model. These components should fit perfectly with a bit of modification...

I designed a stand specifically for my son's Traxxas Slash 4x4 1:10 scale vehicle so he could store it safely with the wheels off the ground. This setup is allegedly crucial in maintaining the round shape of the wheels and preserving the shocks and...

You will need 11mm x 4mm bearings/bushings for a 1:10 scale Traxxas 2wd vehicle. The stock type on a Stampede should fit directly, although it may require some minor modifications to make them work perfectly. This axle was designed entirely from...

This i a wheels which fits the Traxxas Slash.

This is a wheel that matches the Traxxas Slash perfectly.

This is a direct replacement for the popular Traxxas E-Revo Integy Wheelybar. ...Enjoy the experience.