traxxas stampede chassis 3d models

Traxxas Stampede Battery Clamp. ...Two separate designs cater to varying battery heights, mirroring the original clamp's dimensions exactly.

Traxxas camber link on a stampede. Traxxas part number 3641A. Printed at 100% infil. This is PETG, it held up good. ... I haven't tried PLA yet.

Replacing the worn-out VXL chassis on my Traxxas Stampede 2WD means installing a durable new spindle, one that will take a pounding without sacrificing control. The original design often starts to wear down quickly due to constant use, making every...

This is a bespoke rear body mount designed specifically for the Traxxas Stampede, although I'm not entirely certain whether it will fit other Traxxas models as well. It's perfect for mounting custom bodies or simply wanting more flexibility in your...

I misplaced the clip holding my Traxxas Stampede's battery, prompting me to take precise measurements and design an alternative solution from scratch. ...The result is surprisingly streamlined, yet effectively serves its purpose with remarkable...

Traxxas camber link on a Stampede. Traxxas part number 3641A. This is PETG, and it held up great. I haven't tried PLA yet. I printed at 100% infill. This model was run on a custom Delta printer. No raft or supports were used. ...The resolution was set...

Spring spacers for the Traxxas Stampede are designed to preload shock absorbers with precision. Available in various thicknesses, including 2, 3, 4, and 5 millimeters, these spacers ensure a consistent and controlled ride. ...By optimizing shock...

This my new cool rear led bar for my traxxas stampede! I add a support for the button LED bar. The skull was found on thingiverse, thanks to recklesstryg for the model :) I print it without bed. ...Like it ;) Edit: 25/05/2017 I made an cool...

These are front and rear airless tires specifically designed for a Traxxas Stampede. I haven't had the chance to print and test these yet. They're intended to be printed with a low infill setting (under 25%) using TPU or any other flexible material.

This is a ESC mount system for an Traxxas Stampede. Beside other Systems, it is more space efficient. I have installed an Hobbywing Xerun XR8 SCT with an Hobbywing Xerun 3660 SD G2 3200kv motor. Due to the size of the motor, I had to remove one...

This is a custom tie bar designed for the Traxxas Stampede front end. Instead of buying a standard fiberglass or aluminum one, I decided to create my own in TinkerCAD. So far, it's untested on an RC vehicle. The model was printed using PLA at 100%...

The mount is designed specifically for a Stampede bumper and attaches with three bolts that pass through the three holes in the bumper and the mount's 1/4 inch holes. Since I haven't tested it yet, my current prototype consists of only drilled holes,...

I crafted a robust upgrade for my 2WD Stampede - a durable replacement bar made from high-quality TPU that's virtually indestructible. To maximize its performance, I suggest printing it in ABS or the premium choice of TPU or Polycarbonate, ensuring...

If you want the full tutorial, click on this link: http://www.cochesrc.com/foros/monster-trucks-electricos-escalas-1-10-1-8/1887884-tutorial-conversion-stampede-truggy-stampede.html but be sure to use a translation website since I wrote it in...

In addition I have upload the full chassis if you can print it for the big size on your printer if not, you can use the aluminium chasis of other car just like me on the V1. Of course, when you buy the back aileron, be sure that it can fit...

This is a custom-built Conestoga trailer tailored specifically to my Traxxas Stampede 4x4 VXL, crafted from the ground up using Tinkercad's intuitive design tools.

ESC mount plate for a Hobbywing 10BL60. ...Fits Traxxas Stampede VXL models and possibly more. ...For strength, it is better to use double-sided tape You will need the following hardware for installation: - 2 x 16 mm hex cap screws

Traxxas Hoss/Stampede ESC mounting plate(will not fit old stampede 4x4) modifying may be necessary in yellow circled areas, I used a dremel to sand down the area for antenna routingThe picture of the bottom of the plate with esc screwed in is the...

You can easily install a Hobbywing EZ Run 60A ESC onto your Traxxas Stampede 4x4 Chassis. This mount securely holds both the ESC and the necessary capacitors in place, while also accommodating the small black switch that controls the system. The blue...

I built a custom adapter to fit RC4WD Predator tracks onto my Traxxas Stampede, since there isn't an official one available from RC4WD. This has worked out great on my 2WD Stampede model. I drive across deep snow in our yard and it performs...

I've modified the Traxxas Nitro Stampede with an .18 sized glo engine from Hobby King, making it way too powerful for its original 4-wheel capability. In an attempt to move as much weight forward as possible, I've moved the RX battery box up. ...This...

Mounting a rear extension on your Traxxas Stampede 2WD can be an excellent way to enhance its overall performance and stability, especially when paired with a larger body. ...This modification allows the vehicle to maintain better traction and control...

Rear Left Lower Control arm for Traxxas Stampede. I printed in PLA and ran the layer lines along the angle of the shock and it has held up so far. Abs or pla+ would probably hold up better. ...Drew it according to dimensions of stock part.

This mount for the Traxxas Stampede puts the SkyRC GSM020 GPS under the rear 'bed' to keep it out of the way. Quick and easy print (about an hour). This fits the stock rear body mounts. ... You'll need: 2 x M3x20mm cap head bolts (18mm also work)

Needed a way to hang my RC cars on the wall, so I made this on to fit my Traxxas Son-uva Digger 2WD Monster Truck. The hanger fits all Stampede 2WD based models e.g. ...Bigfoot, Gravedigger, Monster Mud etc.

Battery strap for Traxxas Stampede. I wanted one with a retainer clip to keep the wires and balance lead from flopping around, so I designed one on Meshmixer. ...There are 2 files - one has a spacer underneath for thinner batteries and another without a...

This mount for the Traxxas Stampede puts the SkyRC GSM020 GPS under the rear 'bed' to keep it out of the way. Quick and easy print (about an hour). ...This fits the stock rear body mounts.</p><p>You'll need:<br>2 x M3x20mm cap head bolts (18mm also...

This custom rear mount post empowers users to integrate a Rustler body shell onto a Stampede chassis, unlocking new possibilities for their vehicles. ... Print Settings Printer: Wanhao Duplicator 4 Rafts: No Supports: Yes Resolution: 0.25 Infill: At...

Part Number: 3638 Guaranteed to Fit the Traxxas Rustler Vehicle with Precision and Ease.

Remix fixes Scaling issue of OP design. ... Added Traxxas name to the Bracket.