traxxas slash wheelie bar 3d models

The driver's choice is a reduced spring support for the suspension system of the Traxxas Slash 1/10 Scale RC Car. ...A redesigned model available on Thingiverse, design reference number #1175692.

this is the traxxas slash 1/10 scale battery adapter post. ...fits fine in the chassis.</p> <h3>Print instructions</h3><p>Unassociated tags: r/c<br/> Category: R/C Vehicles</p>

the lower shock spring support for the suspension on the 1/10 scale traxxas slash. ...version with shield http://www.thingiverse.com/thing:1175692 Print instructionsUnassociated tags: r/c Category: R/C Vehicles

The front section of the Traxxas Slash 2WD model awaits your attention, pending the first step in bringing it to life – printing it. Has anyone attempted this print? If so, please share the results. Print with 100% Infill Preparation Print...

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. ...I had previously uploaded this with logos but had to remove them.

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. Support are required for the front opening. Supports for...

I needed a roomier wheelie bar for my Hobao MT1, so I borrowed the design from the new HOBAO MT2. All you need is a 3mm rod with fillet and that's all there is to it. ... Best printed with hard TPU 45D, let me know if it works well with other fillaments...

I built a custom HSP 1/16 Monster Truck Wheelie Bar since none were available for purchase. I designed it with 100% infill and divided it into three sections, making it easier to print. ...After printing, the pieces will need to be glued together.

BSR SABERTOOTH Wheelie Bar I'm using standard RC bearings in my wheels - specifically, 5x11x4mm ones. To build this project, you'll need to get your hands on two of these precise bearings. ...Please note that they are a tight fit, so be prepared for...

This design adds a wheelie bar to the Tamiya Clod Buster. To get both sides (left and right) you need to mirror the part in the slicer and print it without any supports. ...The two pieces can be screwed together using the little hole in the middle.

The Traxxas Slash just got a whole lot cooler, thanks to an upgraded front steering block that's been fine-tuned to precision-fit on this 1/10th scale 4x4 beast of a RC car. ...The new bearings slide in with silky smoothness, ready to take the Slash to...

... configurations. The updated design boasts sleek lines and a rugged build that perfectly complements the Slash's aggressive stance, making it a testament to Traxxas' commitment to delivering high-performance products that exceed driver expectations.

After hours of precision measurement and meticulous design, I created four test prints that led me to develop a brand new front bumper bar for the 1:10 scale Traxxas Slash 2wd. This custom part utilizes the original screws and mounting position,...

the 2 holes in the middle of the part are for attaching an additional center brace for extra support. use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm brace for extra support...

... here: http://www.thingiverse.com/thing:1175687) for an added layer of support and peace of mind during high-speed adventures. Don't settle for mediocre performance – upgrade your Traxxas Slash today with this innovative bumper arm design!

EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687 Print...

Traxxas Slash Lowering Kit using stock Suspension. You will need 4 standard slash screws. (can buy off of amazon or use old screws) It reduces front suspension travel and the rear is just lower. Perfect for drag racing or undersized bodies...

Here are some 3D modeling creations I did for the Traxxas Slash. Each part has been thoroughly tested and pushed to its limits on several Slash models. Some components perform exceptionally well in specific materials, such as nylon, which is ideal...

A custom front bumper upgrade designed specifically for the Traxxas Slash 1/10 scale 4x4 RC car, engineered to provide a rugged and aggressive appearance on the track. This modified bumper utilizes the robust mounting system from the RPM aftermarket...

Printed for a Traxxas Slash 2wd. The 4x4 setup is a distinct configuration. This one doesn't utilize bushings or bearings, which may cause it to wear out rapidly. However, it appears to hold up remarkably well nonetheless. ... Thanks for the...

EDIT: Upgraded with advanced new design bumper arm for 1/10 scale Traxxas Slash. Two holes in the middle of the part are specifically designed for attaching an additional center brace to boost support. ...This extra mounting point allows for secure...

The Traxxas Slash battery cover is a vital component that requires attention to detail and precision craftsmanship. ...The sleek design of this cover not only adds an aesthetic touch but also provides protection from the elements, ensuring your...

Updated design now available featuring a rear bumper specifically designed for the 1/10 scale Traxxas Slash. This bumper is intended to be used in conjunction with my printable bumper arm, which can be found at Thingiverse under the ID number...

the lower shock spring support for the suspension on the 1/10 scale traxxas slash. version with shield http://www.thingiverse.com/thing:1175692 Print instructionsUnassociated tags: r/c Category: R/C Vehicles

LED housing to bolt into aftermarket RPM Bumper kit for the traxxas slash 2wd & nitro slash. Uses led extracted from cheap but very bright led lights found at most harbor freight stores Connects into receiver but voltage needs to be reduced...

it has the normal mounting holes in the front for the shock, but it also has mounting holes in the rear so you can mount another shock to the rear of the a-arm (for the rear a-arms only, steering gets in the way on the front) using my printable...

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....

Updated with a fresh design, this is a rear bumper tailored specifically to the 1/10 scale Traxxas Slash. For optimal stability and alignment, it's highly recommended that you use it in conjunction with my printable Bumper Arm, available on...

Here's an updated look for your Traxxas Slash, just a little something to give it some personality. You will find all of the assembly details below: First off, fire up your printer and hit print on both pieces with 100% infill - don't worry about...