traxxas slash wheel wells 3d models

This is a quick-build version of a 35mm battery holder for the Traxxas Slash 4x4. I had to get it ready to race overnight, including printing. Fits into standard battery holder holes/pins but replaces the bridge with a new one that hosts batteries...

I designed these light pods to attach to a stock Traxxas Slash bumper. To install, drill a hole in the bumper and thread an M3 screw through the hole in the bracket and into the bumper. Then stick the LEDs into the other hole. I used some random 5mm...

I designed a simple chassis saver for my Traxxas Slash 2wd with High Centre of Gravity chassis. The original design was made by Proline a few years ago to address the weak point where the transmission bolts to the chassis. However, when Proline...

This is a front shock tower stiffener designed specifically for the Traxxas Slash 2WD - although it's worth noting that this particular model doesn't require as much support due to its body mount. The same goes for the Bandit and Rustler, which can...

traxxas chassis for rustler or bandit, made smaller so can fit on printer bed.

... holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here https://www.youtube.com/watch?v=zTKKWeqSROw&t=501s Skip to 7 minutes

This is the Front Caster Block for a Traxxas Slash 2WD, Bandit or Rustler. Print them if you break one... PLA Holds up okay in mid-temperature and cold. I use PLA for normal racing conditions. I raced for 1 hour accident-free with no breakage. I...

The imbalance between the front and rear of the Traxxas Slash 4x4's original body was a major issue that required attention. I modified leftover parts from the stock body mount using extension body posts, cutting them down to size to raise the front...

Replacment wheel for Traxxas(possibly others) transmitters.

TRAXXAS SUMMIT - wheel cap for 12mm scrue

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

Traxxas rear uprights. Stock look with a little more strength added in with rounds. I haven't printed this yet, just measured and drew it up. ... So it may need a few fixes in the future.

These short arms I designed specifically to accommodate a Lightning McQueen body on a Traxxas Nitro Rustler chassis are quite impressive. ...Stock Bandit rear arms were used in their construction.

Rear wheel well fully redesigned from new sketches to match side skirt mounting holes on original design. More strength, and allows more room fore and aft of the tire to prevent rubbing. Front deflector includes additional mounting point to chassis.

I wanted to mount my old Slash body on the wall so I made this I have not printed this yet so it might not work

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.

Battery Tie Down with a solid center section to allow the mounting of ESC and Receiver as far back on the slash chassis but keeping the weight centered.

I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!

These wheel wells were specifically designed for use in the Axial SCX10 II Kit Cherokee, although I'm not certain whether they would fit other vehicles or body styles. The wheel wells add a scale feature to your rig that sets it apart from others,...

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. ...Uses same holes in chassis as Traxxas original ESC. ... I made it 3mm thick, cut it in your slicer depending on how thick you want it.

These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. ...I have not attempted to print it yet, but the dimensions are the same.

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

for PL 1/10 slash raptor body(real scale) miror when you attach on your toy body, each side needs "dia 2mm, length 8mm, 3screws for each side, total 6 screws need)

The bearings are available from traxxas or here cheaper: http://www.kingheads.com/product_info.php?products_id=934 UPDATE 05/05/15: I've updated the design to allow for two motors with a reverse mount on one side. UPDATE 06/16/15: A friend of mine...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

For my Slash 4x4 ultimate, as a replacement for the original VXL 3S controller The adapter can take controllers up to a maximum width of 40mm Controllers are available here>>> https://amzn.to/33UHdMk Video: https://www.youtube.com/watch?v=74zSqdlPX2Y

I'm doing a slash speed run project without breaking the bank by opting for plastic alternatives instead of metal. They're not only affordable but also incredibly lightweight, making them perfect for printing with ease - the end result is...