traxxas slash snow tracks 3d models

... for the traxxas slash 1/10 scale 4x4 RC car. ...with 10 holes for LEDs this uses the mounts for the RPM aftermarket front bumper mount. Print instructionsUnassociated tags: front bumper, LED bar, LED mount, R/C, traxxas slash Category: R/C Vehicles

... support system engineered specifically for bigbore upgraded shocks in the 1/10 scale 4x4 Traxxas Slash. ... You can find my shock guard design for the stock shocks at https://www.youmagine.com/designs/traxxas-slash-shock-support-and-guard-short

Track sections can be joined together via the individual track links included in the file section. Also included in the file section is the strengthened version of the tracks, the third STL file. Print Settings Printer: Use a Turnigy Fabrikator...

Revolutionized by cutting-edge 3D Slash technology!

GoPro style mount designed to bolt to the chassis of a Traxxas Slash 4X4 (Not sure on 2WD) with recess under the mount to allow for a chassis protector / dust cover.

EDIT: updated with newer design front steering block for the traxxas slash 1/10 scale 4x4 RC car. Print instructionsUnassociated tags: r/c Category: R/C Vehicles

This is a body mount for a traxxas slash. It was used to change the body to a larger model. ...I belive it is about 77 mm ish, heavy on the ish.

This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL as it spent far too much time on its roof! In addition to the printed parts you will need the following parts: 2x 625 bearings 2x M5x20 countersunk head bolts 2x BS210 O-rings 4x...

Risers are sized for Slash tire size, Rustler and Bandit conversions will have the front sitting a bit higher than stock which is probably a good thing if snow is deeper than 1". Mounts to the stock C hub with stock hardware. All parts are fully...

This innovative cap securely fits over the Titan 12T 550 motor in your Traxxas Slash, enhancing performance and style. **Installation Guide** For a seamless build experience, follow these steps: Print with minimal 5% infill settings without the...

not necessary but improves strength. mounts between the 2 bumper arms giving extra support use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm http://www.thingiverse.com/thing:1175688 Print...

This is an expanded body posting for the "Traxxas Slash Battery Adapter" by Sciencepotato, available at https://www.thingiverse.com/thing:1175694 . ...I have only made a hole for the very top slot but will update this post to include other positions as...

This is a component to fasten a thicker rechargeable battery (25 mm high, eg. ...LiPo Pack 5000mAh) in the TRAXXAS Slash 4x4. You can use the original bow to push it into the component. Please notice: you have to unscrew the stud a little bit. ...

Updated with a fresh new look, a high-performance front bumper is now available for the Traxxas Slash 1/10 Scale 4x4 RC Car. ...Equipped with 10 strategically placed holes for LED lighting, this durable design leverages the mounts provided by RPM's...

I designed this using Tinkercad because there was nothing for me to mount my Hobbywing Ez10 ESC on the Traxxas Slash LCG Chassis with the shorter wires coming from the Hobbywing motor. Printed on both my Prusa MKS3 and Ender 3v2 using .2mm layer...

These two components form the essential part of the rear bumper attachment system in the Traxxas Slash, a highly versatile 1/10th scale four-wheel drive RC vehicle. ...I have carefully designed and incorporated an integrated hitch bracket onto the upper...

I tried to print "Traxxas Slash Motor Cap V2" from "XYZAidan" https://www.thingiverse.com/thing:498013 Thanks a lot for the inspiration. But without support Material I couldn't print it. And the support material was hard to remove and some of the...

The hole pattern fits Integy RC Model T8026 Steel Roll Cage Body for Traxxas 1/10 Slash 2WD. Though you can also mount it to the shell by drilling 4 holes. Also here is the controller mount. you can use it to attach an FPV screen to your...

The hole pattern fits Integy RC Model T8026 Steel Roll Cage Body for Traxxas 1/10 Slash 2WD. Though you can also mount it to the shell by drilling 4 holes. Also here is the controller mount. you can use it to attach an FPV screen to your controller...

I upgraded my Traxxas BEC to handle higher voltage servos, but I ran into an issue with the included spacer - it doesn't fit with the Slash Rx enclosure design. After searching for a solution, I discovered that the necessary o-ring is only available...

This is a straightforward flat ESC Mount designed to seamlessly fit into the stock ESC location on both the stock Traxxas Slash 2WD Chassis and the Low Center of Gravity (LCG) Chassis. It might also work with other models that utilize the XL-5 ESC,...

I'm designing a straightforward fan plate meant to attach to the Traxxas Slash - the fan itself doesn't rotate. When creating this design, my goal was to give my Slash a more Short Course or Trophy Truck appearance. However, after printing one, I...

I design a reinforced bumper arm system for the 1/10 scale Traxxas Slash, adding essential support to enhance performance. A specially crafted metal bracket secures between the existing bumper arms, ensuring stability and robustness. Combine with...

This is an evolution of the original Traxxas part for Slash. Fit the 4WD and maybe the 2WD. Made for 40mm height battery pack (max 14,5cm long). Ask me if you need an other height. This one is a lightweight version. Maybe not resistant...

This is a customized Drift wheel designed specifically for my 4x4 Traxxas Slash. I've been eager to try out drifting and didn't want to purchase an entirely new vehicle. I fabricated the face flush for hassle-free printing. Additionally, I created...

A sleek new front bumper has been designed specifically for the Traxxas Slash, a 1/10 scale 4x4 radio-controlled vehicle. This rugged accessory features ten strategically placed holes for LED lights, adding an extra layer of visibility and style to...

I designed a mount for my Sidewinder 3 to complement my Traxxas Slash, and it was done in no time. Although this mount comes equipped with small screw holes, they aren't really necessary due to how snugly the switch fits into place. A hole is...

These protective covers fit onto the rear shock absorbers of a Traxxas Slash to keep dirt out of/clog-prone areas around the shocks. I've recently updated my design with an improved version called ShockGuardV2.stl; I highly recommend using this...

This updated part is designed specifically for the Titan 12T motor found in the Traxxas Slash 2wd. However, it may also fit other motors as well.\n\n \n \n Assembly Instructions First, print the design...

This is a double tube Baja style bumper for your Traxxas Slash (LCG) and Rally. This really gives your Slash/Rally, with the VW Bug body, a realistic look. I printed this in black PETG. The bottom piece i was able to print in high quality. The top...