traxxas slash snow plow 3d models

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

These short arms I designed specifically to accommodate a Lightning McQueen body on a Traxxas Nitro Rustler chassis are quite impressive. ...Stock Bandit rear arms were used in their construction.

Traxxas rear uprights. Stock look with a little more strength added in with rounds. I haven't printed this yet, just measured and drew it up. ... So it may need a few fixes in the future.

Battery Tie Down with a solid center section to allow the mounting of ESC and Receiver as far back on the slash chassis but keeping the weight centered.

Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!

I wanted to mount my old Slash body on the wall so I made this I have not printed this yet so it might not work

... 3300Kv brushless motor I bought on Amazon. ...Printed out of PLA, I have only had one strip so far while driving WOT in deep-ish snow with the snow slingers on all 4 wheels. Might last longer out of PLA+/Tough PLA. ... .2mm layer height 100% infill

Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. ...Uses same holes in chassis as Traxxas original ESC. ... I made it 3mm thick, cut it in your slicer depending on how thick you want it.

These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. ...I have not attempted to print it yet, but the dimensions are the same.

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

for PL 1/10 slash raptor body(real scale) miror when you attach on your toy body, each side needs "dia 2mm, length 8mm, 3screws for each side, total 6 screws need)

A simple plate for mounting esc's to the slash. Uses stock mounting holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here...

I'm doing a slash speed run project without breaking the bank by opting for plastic alternatives instead of metal. They're not only affordable but also incredibly lightweight, making them perfect for printing with ease - the end result is...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

For my Slash 4x4 ultimate, as a replacement for the original VXL 3S controller The adapter can take controllers up to a maximum width of 40mm Controllers are available here>>> https://amzn.to/33UHdMk Video: https://www.youtube.com/watch?v=74zSqdlPX2Y

I have not attempted to print it yet, but the dimensions are the same. Print instructionsCategory: Toys & Games Summary These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear...

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

Printable paddle tires compatible with Traxxas 2wd vehicles. REQUIRES NO GLUE FOR THE TIRES there are "locking lugs" on both wheel and tire to keep it from rotating on the wheel. (6) 3x12mm screws are required to assemble wheels. These smooth...

The bearings are available from traxxas or here cheaper: http://www.kingheads.com/product_info.php?products_id=934 UPDATE 05/05/15: I've updated the design to allow for two motors with a reverse mount on one side. UPDATE 06/16/15: A friend of mine...

Made a custom mounting solution for the joystick that seamlessly integrates with the cupholder, eliminating the need for any drilling into the dashboard! The design was carefully crafted to specifically work in conjunction with an Arctic Heavy Duty...

Made a custom mount for the joystick which integrates seamlessly with the cupholder, eliminating the need for any dash drilling! ...This design was tailored specifically to pair perfectly with the Arctic Heavy Duty big joystick and complement the 2010...

This is a WIP and will receive updates this works with arma vorteks and granite it slots into the circle indent on the bumper and go's under the Body

... of the tire and the outer diameter of the ring are about the same. The idea is that the rubber will still contact and the studs will improve grip. These should work on the 2wd slash rear wheels, may need to be redesigned for the front wheels.

rear suspension mount without gearbox cover traxxas slash 4wd remo hobby 9emu