traxxas slash skis 3d models

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

These short arms I designed specifically to accommodate a Lightning McQueen body on a Traxxas Nitro Rustler chassis are quite impressive. ...Stock Bandit rear arms were used in their construction.

Traxxas rear uprights. Stock look with a little more strength added in with rounds. I haven't printed this yet, just measured and drew it up. ... So it may need a few fixes in the future.

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

Battery Tie Down with a solid center section to allow the mounting of ESC and Receiver as far back on the slash chassis but keeping the weight centered.

Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.

I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!

I wanted to mount my old Slash body on the wall so I made this I have not printed this yet so it might not work

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. ...I have not attempted to print it yet, but the dimensions are the same.

Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. ...Uses same holes in chassis as Traxxas original ESC. ... I made it 3mm thick, cut it in your slicer depending on how thick you want it.

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

for PL 1/10 slash raptor body(real scale) miror when you attach on your toy body, each side needs "dia 2mm, length 8mm, 3screws for each side, total 6 screws need)

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

For my Slash 4x4 ultimate, as a replacement for the original VXL 3S controller The adapter can take controllers up to a maximum width of 40mm Controllers are available here>>> https://amzn.to/33UHdMk Video: https://www.youtube.com/watch?v=74zSqdlPX2Y

I'm doing a slash speed run project without breaking the bank by opting for plastic alternatives instead of metal. They're not only affordable but also incredibly lightweight, making them perfect for printing with ease - the end result is...

A simple plate for mounting esc's to the slash. Uses stock mounting holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here...

I have not attempted to print it yet, but the dimensions are the same. Print instructionsCategory: Toys & Games Summary These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear...

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

The bearings are available from traxxas or here cheaper: http://www.kingheads.com/product_info.php?products_id=934 UPDATE 05/05/15: I've updated the design to allow for two motors with a reverse mount on one side. UPDATE 06/16/15: A friend of mine...

The Traxxas Ski is designed to fit a 12mm hex.

rear suspension mount without gearbox cover traxxas slash 4wd remo hobby 9emu

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7j0i2NNop47

it is my rendition of the rpm style bumper  will need to print with supports

Please provide the original text that needs to be spun, so I can assist you in generating a new version of it while retaining its core information and meaning, but with restructured sentences and different wording. ...Kindly keep your request within 60...

For a backslash, I type \.

just line up and screw on