traxxas slash inner fender 3d models

The Traxxas Slash just got a whole lot cooler, thanks to an upgraded front steering block that's been fine-tuned to precision-fit on this 1/10th scale 4x4 beast of a RC car. ...The new bearings slide in with silky smoothness, ready to take the Slash to...

... configurations. The updated design boasts sleek lines and a rugged build that perfectly complements the Slash's aggressive stance, making it a testament to Traxxas' commitment to delivering high-performance products that exceed driver expectations.

... here: http://www.thingiverse.com/thing:1175687) for an added layer of support and peace of mind during high-speed adventures. Don't settle for mediocre performance – upgrade your Traxxas Slash today with this innovative bumper arm design!

EDIT: updated with newer design a rear bumper for the 1/10 scale traxxas slash use with my printable bumper arm http://www.thingiverse.com/thing:1175688 and printable bumper arm brace for extra support http://www.thingiverse.com/thing:1175687 Print...

the 2 holes in the middle of the part are for attaching an additional center brace for extra support. use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm brace for extra support...

A custom front bumper upgrade designed specifically for the Traxxas Slash 1/10 scale 4x4 RC car, engineered to provide a rugged and aggressive appearance on the track. This modified bumper utilizes the robust mounting system from the RPM aftermarket...

Here are some 3D modeling creations I did for the Traxxas Slash. Each part has been thoroughly tested and pushed to its limits on several Slash models. Some components perform exceptionally well in specific materials, such as nylon, which is ideal...

Printed for a Traxxas Slash 2wd. The 4x4 setup is a distinct configuration. This one doesn't utilize bushings or bearings, which may cause it to wear out rapidly. However, it appears to hold up remarkably well nonetheless. ... Thanks for the...

the lower shock spring support for the suspension on the 1/10 scale traxxas slash. version with shield http://www.thingiverse.com/thing:1175692 Print instructionsUnassociated tags: r/c Category: R/C Vehicles

EDIT: Upgraded with advanced new design bumper arm for 1/10 scale Traxxas Slash. Two holes in the middle of the part are specifically designed for attaching an additional center brace to boost support. ...This extra mounting point allows for secure...

The Traxxas Slash battery cover is a vital component that requires attention to detail and precision craftsmanship. ...The sleek design of this cover not only adds an aesthetic touch but also provides protection from the elements, ensuring your...

Updated design now available featuring a rear bumper specifically designed for the 1/10 scale Traxxas Slash. This bumper is intended to be used in conjunction with my printable bumper arm, which can be found at Thingiverse under the ID number...

it has the normal mounting holes in the front for the shock, but it also has mounting holes in the rear so you can mount another shock to the rear of the a-arm (for the rear a-arms only, steering gets in the way on the front) using my printable...

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...

Updated with a fresh design, this is a rear bumper tailored specifically to the 1/10 scale Traxxas Slash. For optimal stability and alignment, it's highly recommended that you use it in conjunction with my printable Bumper Arm, available on...

This is an essential part of the Traxxas Slash's wheels system. The hub cap securely connects to the bolts that keep the wheel in place. Currently, you need to use a screwdriver to carefully pry off the hub cap. I plan to make improvements to this...

These are custom shields designed to fit onto the rear shocks of a Traxxas Slash, preventing dirt from accumulating and clogging the shock absorbers. A newer version, known as ShockGuardV2.stl, is available for use, which is recommended over the...

Here's an updated look for your Traxxas Slash, just a little something to give it some personality. You will find all of the assembly details below: First off, fire up your printer and hit print on both pieces with 100% infill - don't worry about...

EDITED VERSION, FRESH DESIGNS INCLUDED Updated designs come with a reinforced bumper arm now available in 1/10 scale traxxas slash format. Two strategically positioned holes run through the center of this robust part allowing for an extra stabilizing...

This is the updated design for the 1/10 scale 4x4 Traxxas Slash's A-Arm. It features standard mounting holes in the front for shock installation, as well as additional holes at the rear to accommodate a secondary shock mounted using my printable...

This is the a-arm for the 1/10 scale 4x4 Traxxas Slash. It features standard mounting holes at the front to secure the shock, but it also includes additional holes at the rear, allowing you to attach another shock to the back of the a-arm...

After hours of precision measurement and meticulous design, I created four test prints that led me to develop a brand new front bumper bar for the 1:10 scale Traxxas Slash 2wd. This custom part utilizes the original screws and mounting position,...

Updated with New Design This A-Arm Works Perfectly for the 1/10 Scale 4x4 Traxxas Slash Vehicle. It Includes Normal Mounting Holes at the Front for the Shock Absorbers and Extra Holes at the Rear to Attach Another Shock Absorber. The Mounting Holes...

Rock lights for inner fender 2x 3mm

Simple esc mount and gnss for slash lcg 2wd chassis. If you found this, no explanation is needed. ...Enjoy!!

I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.

I wanted to drift my Slash so I designed so sweet drift covers for the tires, they are very tight fit, but once you get them squeezed on they drift so awesome, and with the plus of using way less time and fillement than making a whole tire, I did try...

This mount/bracket allows you to keep the entire antenna mounted under the body of the slash. It just clips on to the chassis. It also has an eyelet that allows for you to attach a tether to the battery retainer clip. It is best to print upside down....

After bashing a dozen packs through my Slash with this Rx box in place, it's the only part that still bothers me. Again, this is not waterproof; however, it is fairly effectively water-resistant. With shoe goop, you could easily make it watertight,...