traxxas slash inner fender 3d models

This job is to repair the faulty gas cap retainer clip on my nitrous oxide system.

I built the front and back sections vertically with support in place. It took around 7 hours to complete the back section, while the front portion required about 9 hours of printing time. I used an Ultimaker 2+ printer with PLA filament at a normal...

Remix , just added some structure to be able to print without support under the guard But for my shocks it was too small, just created a bigger one for bigger shocks with bigger diameter : https://www.thingiverse.com/thing:4855113

Print full size and use a body clip to secure pin in place. The plow is 300 millimeters wide, so keep this measurement in mind when handling it. Please post a make if you decide to print this model. This design is somewhat fragile, so drive slowly...

We're upgrading to a stealthier bumper that beats out the factory standard model by a mile. ...What makes can we expect from this new design?

This will perfectly fit over your ESC and bolt securely onto your car using the original VXL mounting holes.

ENThese spacers for 4x4 LCG chassis allow you to fit a 2S LiPo battery in a hardcase into battery tray with stock hold-down retainer.RUДанные проставки позволяют вместить 2S LiPo аккумулятор в жёстком корпусе.

you can use this for lift your body. ... Print 100% infill, 0,2mm layerheight

Adjustable so you can run regular packs or shorty. The arrangement of the holes and notches allow 2mm incremental movement. ...A 2mm pin is required for the hinge, 2mm bolts and nuts hold the notched piece in place, and 2mm bolts to attache the tabs to...

Printed with TPU using 50% infill without supports. Used with https://www.thingiverse.com/thing:5150262 to create a head tracking FPV mount for my 19mm camera. Mounts right in front of the receiver case/antenna. Note, it will block the antenna. I...

A simple mirror of the source project to accommodate both sides of the vehicle. ...With the two files you can have the tread direction going in the same direction on both sides.

I often encounter issues with this part, which is why I've been accumulating broken pieces over time. To get started, you'll need the component and some heat to melt away the old plastic and insert the metal ball's pegs into the holes without it...

Remix , just added some structure to be able to print without support under the guard But for my shocks it was too small, just created a bigger one for bigger shocks with bigger diameter : https://www.thingiverse.com/thing:4855113

The is a kitbash of the original. I made the front decks thicker to better take a hit. to get the densest deck print on edge into z territory. ... I will be designing a break away system that will self correct after impact.

Its my first project

Same part as https://www.thingiverse.com/thing:3353778 just gave it a flat for easier printing.

Designed for 4x2 Low Center of Gravity chassis, this model may also be suitable for 4x4 chassis. To assemble the two parts, six M3x16 screws are required: three to join the components together and another three for securing it onto the chassis - four...

I Made This Quick Adapter For A Buddy Of Mine, Perfectly Suited For Up To A 30mm Tall Battery That's Mounted Sideways, And Allows Straps To Be Run Underneath The Battery For Secure Holding In Place. No Fussing With Breakable Tabs Here, But You'll...

Customized version of https://www.thingiverse.com/thing:5821740 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5821740

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/cZjAdEeieFQ

I was hunting for a front bumper that would perfectly replicate the sleek design of a Losi 8ight's front bumper for my Backslash project, but unfortunately, my search fell flat. Undeterred, I decided to take matters into my own hands and create one...

My pro-line bead lock rims seem to have a little larger hex inside the rim and it was loose with the stock hex adapters. These are 0.25mm larger and also 0.1mm closer to the axle shim to reduce slop. I used carbon/nylon filament and printed at...

3d print a plate thats used to mount your ESC to your RC car. Use 2 way tape to hold your ESC to the plate which is held on by 2 screws in the original location on the chassis. Plate is 3mm thick. Prints very easy with no supports. 0.3 layer height...

Проставки для увеличения объёма батарейного отсека. Позволяют использовать аккумуляторы ёмкостью 7000..8000 мАч. Устанавливаются между штатными стойками и декой. Для установки потребуются более длинные (+14 мм) винты. Spacers to increase the...

I ran the test on my 1/16 scale model indoors, and it was a blast. I'm happy to create more designs if people show interest. Try one out and let me know what you think. Have fun and stay safe. ... Note: Minimum tip of $5 is required for me to start...

I replaced my old radio and receiver with a Spectrum surface unit, rendering the RPM and temperature sensors obsolete. I sealed off the empty space by plugging the RPM hole with a blanking adapter. ...To ensure a watertight seal, I applied a generous...

In spring, I lost a retainer at the track; rather than buying a replacement, I opted for DIY 3D modeling (first attempt). Constructive feedback is appreciated. As it's untested, durability isn't guaranteed. Thinner areas might cause issues in certain...

I havent Printed this out yet but it is a rough measurement on the battery holder.

This is a a second version of my snow plow, just in time for the cold season. You need a body pin for your truck and some string. Tie the string through the small hole and around somewhere on your chassis to hold the plow at your desired height. ...