traxxas slash bumper 3d models

Updated with fresh design is now the revised front steering block specifically tailored for the Traxxas Slash, a highly regarded 1/10 scale 4x4 radio control vehicle.

Just a simple set of hooks to hang the tires of my traxxas slash off the wall and save some space.

... support system engineered specifically for bigbore upgraded shocks in the 1/10 scale 4x4 Traxxas Slash. ... You can find my shock guard design for the stock shocks at https://www.youmagine.com/designs/traxxas-slash-shock-support-and-guard-short

This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL as it spent far too much time on its roof! In addition to the printed parts you will need the following parts: 2x 625 bearings 2x M5x20 countersunk head bolts 2x BS210 O-rings 4x...

Revolutionized by cutting-edge 3D Slash technology!

This is a body mount for a traxxas slash. It was used to change the body to a larger model. ...I belive it is about 77 mm ish, heavy on the ish.

EDIT: updated with newer design front steering block for the traxxas slash 1/10 scale 4x4 RC car. Print instructionsUnassociated tags: r/c Category: R/C Vehicles

GoPro style mount designed to bolt to the chassis of a Traxxas Slash 4X4 (Not sure on 2WD) with recess under the mount to allow for a chassis protector / dust cover.

See it in action: https://www.meatballracing.com/send-it-merica/ You can buy one of these pre-built from quality Sainsmart TPU (complete with flag!) directly from the designer at MeatballRacing.com...

This innovative cap securely fits over the Titan 12T 550 motor in your Traxxas Slash, enhancing performance and style. **Installation Guide** For a seamless build experience, follow these steps: Print with minimal 5% infill settings without the...

Traxxas TRX4 Sport Off-Road Rock Crawler Heavy-Duty Protection Front Bumper Guard

This is a component to fasten a thicker rechargeable battery (25 mm high, eg. ...LiPo Pack 5000mAh) in the TRAXXAS Slash 4x4. You can use the original bow to push it into the component. Please notice: you have to unscrew the stud a little bit. ...

I tried to print "Traxxas Slash Motor Cap V2" from "XYZAidan" https://www.thingiverse.com/thing:498013 Thanks a lot for the inspiration. But without support Material I couldn't print it. And the support material was hard to remove and some of the...

This is an expanded body posting for the "Traxxas Slash Battery Adapter" by Sciencepotato, available at https://www.thingiverse.com/thing:1175694 . ...I have only made a hole for the very top slot but will update this post to include other positions as...

I designed this using Tinkercad because there was nothing for me to mount my Hobbywing Ez10 ESC on the Traxxas Slash LCG Chassis with the shorter wires coming from the Hobbywing motor. Printed on both my Prusa MKS3 and Ender 3v2 using .2mm layer...

A robust ~110 mm tire tailored for the Traxxas Slash 4x4 or comparable vehicles, ideal for navigating hard packed snow or sand, boasts surprising strength. Print two regular tires along with two mirrored counterparts, both featuring support...

The hole pattern fits Integy RC Model T8026 Steel Roll Cage Body for Traxxas 1/10 Slash 2WD. Though you can also mount it to the shell by drilling 4 holes. Also here is the controller mount. you can use it to attach an FPV screen to your controller...

The hole pattern fits Integy RC Model T8026 Steel Roll Cage Body for Traxxas 1/10 Slash 2WD. Though you can also mount it to the shell by drilling 4 holes. Also here is the controller mount. you can use it to attach an FPV screen to your...

I upgraded my Traxxas BEC to handle higher voltage servos, but I ran into an issue with the included spacer - it doesn't fit with the Slash Rx enclosure design. After searching for a solution, I discovered that the necessary o-ring is only available...

This is a straightforward flat ESC Mount designed to seamlessly fit into the stock ESC location on both the stock Traxxas Slash 2WD Chassis and the Low Center of Gravity (LCG) Chassis. It might also work with other models that utilize the XL-5 ESC,...

I'm designing a straightforward fan plate meant to attach to the Traxxas Slash - the fan itself doesn't rotate. When creating this design, my goal was to give my Slash a more Short Course or Trophy Truck appearance. However, after printing one, I...

This is an evolution of the original Traxxas part for Slash. Fit the 4WD and maybe the 2WD. Made for 40mm height battery pack (max 14,5cm long). Ask me if you need an other height. This one is a lightweight version. Maybe not resistant...

This is a customized Drift wheel designed specifically for my 4x4 Traxxas Slash. I've been eager to try out drifting and didn't want to purchase an entirely new vehicle. I fabricated the face flush for hassle-free printing. Additionally, I created...

I designed a mount for my Sidewinder 3 to complement my Traxxas Slash, and it was done in no time. Although this mount comes equipped with small screw holes, they aren't really necessary due to how snugly the switch fits into place. A hole is...

This updated part is designed specifically for the Titan 12T motor found in the Traxxas Slash 2wd. However, it may also fit other motors as well.\n\n \n \n Assembly Instructions First, print the design...

These protective covers fit onto the rear shock absorbers of a Traxxas Slash to keep dirt out of/clog-prone areas around the shocks. I've recently updated my design with an improved version called ShockGuardV2.stl; I highly recommend using this...

This is the mounting bracket for the rear wheel of my 2WD Traxxas Slash Truck. I manufactured it using PETG material, printing at a slow pace and .12 layer height to boost its structural integrity. So far, I have installed and tested this on my...

PLEASE rate (or leave a comment what is wrong so I can fix it) This is a Traxxas Slash 2WD 28-tooth roughly 48-pinion gear. I used it with the 67-tooth spur gear (posted by me on Thingiverse) and the speed was incredible. Take it easy with the...

My son was fed up with having to constantly remove and reinstall those four pesky body clips every time he wanted to turn on his Slash or swap out the battery and so we decided to create a hinge for the body that attaches neatly to the back bumper.

This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...