traxxas slash body mount extender 3d models

the 2 holes in the middle of the part are for attaching an additional center brace for extra support. use with my printable bumper http://www.thingiverse.com/thing:1175690 use with my printable bumper arm brace for extra support...

After hours of precision measurement and meticulous design, I created four test prints that led me to develop a brand new front bumper bar for the 1:10 scale Traxxas Slash 2wd. This custom part utilizes the original screws and mounting position,...

Here are some 3D modeling creations I did for the Traxxas Slash. Each part has been thoroughly tested and pushed to its limits on several Slash models. Some components perform exceptionally well in specific materials, such as nylon, which is ideal...

the lower shock spring support for the suspension on the 1/10 scale traxxas slash. version with shield http://www.thingiverse.com/thing:1175692 Print instructionsUnassociated tags: r/c Category: R/C Vehicles

Printed for a Traxxas Slash 2wd. The 4x4 setup is a distinct configuration. This one doesn't utilize bushings or bearings, which may cause it to wear out rapidly. However, it appears to hold up remarkably well nonetheless. ... Thanks for the...

Updated design now available featuring a rear bumper specifically designed for the 1/10 scale Traxxas Slash. This bumper is intended to be used in conjunction with my printable bumper arm, which can be found at Thingiverse under the ID number...

The Traxxas Slash battery cover is a vital component that requires attention to detail and precision craftsmanship. ...The sleek design of this cover not only adds an aesthetic touch but also provides protection from the elements, ensuring your...

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...

All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....

This is an essential part of the Traxxas Slash's wheels system. The hub cap securely connects to the bolts that keep the wheel in place. Currently, you need to use a screwdriver to carefully pry off the hub cap. I plan to make improvements to this...

Here's an updated look for your Traxxas Slash, just a little something to give it some personality. You will find all of the assembly details below: First off, fire up your printer and hit print on both pieces with 100% infill - don't worry about...

Updated with a fresh design, this is a rear bumper tailored specifically to the 1/10 scale Traxxas Slash. For optimal stability and alignment, it's highly recommended that you use it in conjunction with my printable Bumper Arm, available on...

These are custom shields designed to fit onto the rear shocks of a Traxxas Slash, preventing dirt from accumulating and clogging the shock absorbers. A newer version, known as ShockGuardV2.stl, is available for use, which is recommended over the...

A horse with a saddle that fits properly.

Today I am adding another project, which is replacing the housing clips with nuts. Design made for Revo 3.3 but will fit derivative models. Additionally, I placed a universal flat support. ... Please check my other projects

This precision-crafted spur gear is specifically designed for the Traxxas Slash, boasting exceptional performance tailored to 3D printing. ...Photo-polymer resin proves itself a reliable choice, delivering superior structural integrity and minimizing...

EDITED VERSION, FRESH DESIGNS INCLUDED Updated designs come with a reinforced bumper arm now available in 1/10 scale traxxas slash format. Two strategically positioned holes run through the center of this robust part allowing for an extra stabilizing...

After bashing a dozen packs through my Slash with this Rx box in place, it's the only part that still bothers me. Again, this is not waterproof; however, it is fairly effectively water-resistant. With shoe goop, you could easily make it watertight,...

I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.

Standard M3x16 ~ M3x20 cap screws will bolt the cover down. It's designed based off the Slash LCG chassis, but it should fit anything that uses the same part. In theory.</p> <p>UPDATE: New version of the top uploaded that adds 0.5mm of clearance...

This modification fits my Slash perfectly, although the holes are slightly undersized once printed in PLA and required a bit of reaming with a round file to match the design's oversized specifications. I left some space for inserting the C-clip, but...

I wanted to drift my Slash so I designed so sweet drift covers for the tires, they are very tight fit, but once you get them squeezed on they drift so awesome, and with the plus of using way less time and fillement than making a whole tire, I did try...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Hi guys ! ... This is a simple piece for the Injora magnetic body mount. Body mount is here : https://amzn.to/3QsHTUt The original front body mount is 1cm too long for the magnetic thing... ... Perfectly adapted for Traxxas TRX4 (Defender for me).

DE:\r\nThese are body caps for Pro Line's body holders.\r\n\r\nTo install, use a soldering gun to press the press-in nut into the cap.\r\n\r\nThread insertion details:\r\nThread type: M4\r\nSize specification: M4x4x5

Using a soldering iron, an EPT stud (or screw) must be driven into each cap until fully seated and level with the outer edge of the body clip. This insert has metric dimensions: Thread type: Unified coarse Gauge size: #10-32 Nominal pitch: . ...060

... die Kappe Gedrückt. Gewindeeinsatz: Gewinde: M4 Größe: M4x4x5 EN: These are caps for the Body Holder from Pro Line. For this purpose, the press-in nut is pressed into the cap by means of a soldering iron. ... Thread insert: Thread: M4 Size: M4x4x5

a big beefy battery mount that has stood up to a lot of abuse. Print instructionsUnassociated tags: r/c Category: R/C Vehicles

... paved roads. ...Its numerous benefits include exceptional traction on dirt and grass surfaces. Additionally, this wheel boasts an impressive amount of grip, making it a versatile option that can be mounted on either side (printed in PLA with supports).