traxxas slash 4x4 inner fenders 3d models

Traxxas Slash Battery Compartment Holder (for large LiPo batteries approximately 40mm) LCG. Printed with the Anycubic i3 Mega and Cura 3.6.0 software. Layer height: 0.16 mm. First layer extrusion multiplier: 120%. Infill density: 100%. Printing...

Mount for the Castle Creations Sidewinder SCT within a Traxxas Rally/Slash with a LCG chassis. There is a ziptie holder on the far end of the switch to hold the motor wires in place as well. You'll need one M3x8mm and M3x12mm cap head screw for...

Gyro mount for the Traxxas Slash, Revo, Summit 1/16 (mini). This mount gives you a flat surface to mount a gyro on your Traxxas 1/16 Rc car. It will only work if you use one servo, as it utilizes the spare servo mount. You can mirror it in your...

Mount for the Hobbywing Max10 SCT within a Traxxas Rally/Slash with a LCG chassis. There's a cutout for the temp sensor as well as it's pretty close.</p><p>You'll need one M3x8mm and M3x12mm for mounting. ...The ESC and switch should friction mount...

Mount for the Hobbywing Max10 SCT within a Traxxas Rally/Slash with a LCG chassis. There's a cutout for the temp sensor as well as it's pretty close. You'll need one M3x8mm and M3x12mm for mounting. The ESC and switch should friction mount though...

Customized version of https://www.thingiverse.com/thing:4381135 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4381135

I use this with the low gravity kit for the Traxxas Slash 2WD. I start by screwing the longest chassis pin in at the back end of the car (backwards from Traxxas), and start the shorter wheel pin at the front end of the car (same as Traxxas). This...

Replacement steering linkage for Traxxas Slash 1/16 and others. This is only for use with only one servo, unlike the original. If it shows popular I could modify it for two servos. May not be as strong as the original part depending on your choice...

This is a 46p, 67t (67 teeth) spur gear I made for my Traxxas Slash 2WD 1/10. It's probably the fewest teeth on a spur gear that will work in combination with a 23 pinion gear. This baby zooms on my RC, but you really need to ease into the throttle...

The mounting holes allow it to be securely attached to the Traxxas Slash 2WD stock chassis as well as the 2WD LCG chassis. A convenient feature of this mount includes a spot where you can place the switch with narrow cutouts that tuck the wires...

... This is a 70 tooth Traxxas Slash 2wd spur gear, similar to part 4370. I have not yet tried with my 550 motor because the 76 tooth spur/23 tooth pinion combo provides a nice balance of acceleration and speed without melting my 550 brushed OOB motor.

Hi, This is a custom mount for my Team Orion Vortex R10 ESC / speed controller installed on a standard Traxxas Slash frame. A friend's suggestion inspired this approach. The mount will firmly press down the ESC once it's securely attached to the rc...

Hi, This is a mount for my Team Orion Vortex R10 ESC / speed controller to be mounted on a stock Traxxas Slash frame. A friend gave me the idea to make it this way. The mount will press down the ESC once it's bolted to the frame of the rc car. It...

Front bulkhead (2530) for a variety of different Traxxas vehicles (Bandit, Slash, Stampede, Rustler, SRT). I have fit this up and confirmed it to be compatible (dimensionally) with the original SRT double deck chassis. Arms have been confirmed to...

This is an ESC mount to fit a Castle Creations Sidewinder 3 ESC in a Traxxas Slash LCG chassis. It firmly holds the ESC in place with or without the fan. It also has a mount for the switch. The lower plate is held to the chassis with either 2 or 3...

This is an ESC mount to fit a Castle Creations Sidewinder 3 ESC in a Traxxas Slash LCG chassis. It firmly holds the ESC in place with or without the fan. It also has a mount for the switch. The lower plate is held to the chassis with either 2 or 3...

This mounting box and top clamp are designed specifically for installing a Mamba X speed controller into a Traxxas Slash 2WD with a lower center of gravity chassis (LCG). First, place the ESC into the printed frame. Next, align the frame holes on...

Mount for the Castle Creations Sidewinder SCT within a Traxxas Rally/Slash with a LCG chassis. There a ziptie holder on the far end of the switch to hold the motor wires in place as well.</p> <p>You'll need one M3x8mm and M3x12mm cap head screw for...

Front 25 degree caster blocks for a variety of Traxxas 2WD vehicles (Rustler, Stampede, Slash, Bandit) with the bearing in hub design. The stock caster blocks on these vehicles have no angle, and therefore match the chassis kickup angle of 30...

This design features a Traxxas 46P 76-tooth spur gear, among others and pinions, which I use for my Slash 2WD RC car. This high-quality, accurately measured 20th generation design is currently my go-to racing setup and prints well even on my basic...

ESC plate for LCG slash 2wd to mount max 10 esc and power button

... as a sacrificial part to prevent damage to the main component. You'll need 2 flags (any type will do), some M3 hardware (socket head screws and regular nuts), and it fits perfectly on a classic Traxxas brand wheelie bar. ...I hope you love it!

I created these 0-degree A-Arms to reduce the terrible oversteer caused by the stock 30-degree bulkhead on the Traxxas Rustler 2WD, with speedruns in mind. ... You will need: - Adjustable steering and camber links (VXL models should have this...

I recently raced in my first organized oval race and quickly realized that my HCG chassis Slash doe not handle well enough to be competitive in any way. I'm not out there for anything more than to have fun, but when I keep rolling over in the...

I created these 0-degree A-Arms to reduce the terrible oversteer caused by the stock 30-degree bulkhead on the Traxxas Rustler 2WD, with speedruns in mind. You will need: Adjustable steering and camber links (VXL models should have this already)...

THIS IS A MODIFIED VERSION OF THE TRAXXAS PART 3736. IT'S MUCH THICKER THAN THE ORIGINAL PART AND I BELIEVE IT'S ALSO MORE DURABLE, EVEN WHEN PRINTED WITH PLA, THANKS TO THIS EXTRA THICKNESS. ... THERE ARE ACTUALLY LEFT AND RIGHT PARTS, AS THE THICKER...

Also check out my rear wing I remixed - https://www.thingiverse.com/thing:2563321 I designed a front wing to boost speed on my traxxas rustler, perfect for high-speed runs. This custom part generates substantial downforce at speeds above 45mph,...

... have got you covered. Plus, they come in two convenient types: left and right wheels, ensuring a perfect fit every time. With a quick print time of under 2 hours, you can get back to the fun stuff – racing your mini Slash vxl through the dirt!

This upgrade features a sturdy 12mm hex nut, carefully resized to perfectly fit the mini Slash vxl. Print enthusiasts are recommended to use this enhanced version, and we suggest utilizing supports during the printing process for optimal results. For...