traxxas slash 4x4 drive shaft 3d models

I often encounter issues with this part, which is why I've been accumulating broken pieces over time. To get started, you'll need the component and some heat to melt away the old plastic and insert the metal ball's pegs into the holes without it...

So I design a rubber component known as Main shaft seal for traxxas slash 4x4 HCG model 1, aimed at covering up the opening in the chassis where the main shaft emerges. Many traxxas slash 4 x 4 owners faced issues with the wide gap between the...

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. ...I had previously uploaded this with logos but had to remove them.

RC Stand for Traxxas Slash 4x4. Included are both HCG & LCG Chassis Stands. HCG is still a work in progress. LCG is complete and the bay has room for the Traxxas EZ Peak+ ID Charger. Support are required for the front opening. Supports for...

GoPro style mount designed to bolt to the chassis of a Traxxas Slash 4X4 (Not sure on 2WD) with recess under the mount to allow for a chassis protector / dust cover.

This is a component to fasten a thicker rechargeable battery (25 mm high, eg. ...LiPo Pack 5000mAh) in the TRAXXAS Slash 4x4. You can use the original bow to push it into the component. Please notice: you have to unscrew the stud a little bit. ...

This is a customized Drift wheel designed specifically for my 4x4 Traxxas Slash. I've been eager to try out drifting and didn't want to purchase an entirely new vehicle. I fabricated the face flush for hassle-free printing. Additionally, I created...

This is a cover for the Traxxas Slash Low Center of Gravity chassis. ...You can print it without any supporting structures.

This design is for use with 12mm hexes, which the Slash 4x4 comes stock with. These should also fit in the rear of 2wd Slash models. I printed these in PLA with .25 layer height with only 2 walls and 10% infill. I tested them out on somewhat rough...

Human: Roll cage I designed specifically for the Slash 4x4 truck mounts directly to the body mounts' attachment holes on the vehicle. The roll cage has only been printed once using Hatchbox Blue PLA, and it hasn't undergone any rigorous testing...

Chose to swap out the foam insert in the battery holder since the fresh lithium-polymer cells I had been using were noticeably shorter than the original Traxxas batteries.

Internal-splined half shaft for Traxxas Slash 4x4.MODEL# 6853A.

It's the measurement from the original part. ... Internal-splined half shaft for Traxxas Slash 4x4. ... MODEL# 6853A.

Mount a Traxxas Slash 4x4 Esc Mounting Plate on Any Vehicle. ...Attach Double-Sided Tape Directly to the Esc, Secure it Firmly in Place on the Plate.

The left front/rear arm is required for my Traxxas Slash 4x4 vehicle, as both the front and rear arms on this model are identical in design.

Adapter plate to mount any esc to a traxxas Slash 4x4. ...Use double side tape to glue the ESC to the plate.

Designed in AutoCAD, this allows for dual motors on a Traxxas Slash 4x4. This been tested in ABS and I've printed them on a Tevo Tornado 3D printer. ...Some filing may be required for perfect fit.

I crafted the Traxxas Slash 4x4 extended body mounts initially, and upon further investigation, discovered that fabricating spacers for the body mount bracket imparts significantly greater strength than the mounts I 3D printed.\r\nThese spacers...

Purchased a brand-new, pre-finished body for my Traxxas Slash 4x4 but it failed to fit properly, prompting me to modify the height of the body mounts instead. ...Following several design iterations, I ultimately settled on three distinct dimensions that...

I designed a stand specifically for my son's Traxxas Slash 4x4 1:10 scale vehicle so he could store it safely with the wheels off the ground. This setup is allegedly crucial in maintaining the round shape of the wheels and preserving the shocks and...

I've designed a custom 3D printed switch mount for my Traxxas Slash 4x4 HCG, specifically to house the brushless motor system's switch. Since it needs to be installed somewhere, I'm providing this file with installation details. To download and...

...I lost the gear cover of my Traxxas Slash 4x4 LCG... :(</p> <p>So I designed my own. It's nearly as perfect as the original piece... but different...</p> <p>Several testprints &amp; model iterations later, I had something that fits ok :)</p>...

I managed to lose the gear cover of my Traxxas Slash 4x4 LCG, which was a real bummer :(. So I came up with my own design. It's nearly as perfect as the original piece, but it has its own unique touches. After several test prints and model...

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

The imbalance between the front and rear of the Traxxas Slash 4x4's original body was a major issue that required attention. I modified leftover parts from the stock body mount using extension body posts, cutting them down to size to raise the front...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

These connect to the slash body mount holes on the stock shock towers and give you a variety of mounting options for bodies with pre-drilled holes, or you can use your own holes. I set them up to use the screw-on caps like the proline mounts... you...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.