traxxas slash 2wd motor fan 3d models

3d print a plate thats used to mount your ESC to your RC car. Use 2 way tape to hold your ESC to the plate which is held on by 2 screws in the original location on the chassis. Plate is 3mm thick. Prints very easy with no supports. 0.3 layer height...

Printed with TPU using 50% infill without supports. Used with https://www.thingiverse.com/thing:5150262 to create a head tracking FPV mount for my 19mm camera. Mounts right in front of the receiver case/antenna. Note, it will block the antenna. I...

The is a kitbash of the original. I made the front decks thicker to better take a hit. to get the densest deck print on edge into z territory. ... I will be designing a break away system that will self correct after impact.

I've printed several versions with varying levels of success. The first version worked well without needing much filing, but I had to file the support angles on subsequent versions to clear the shocks and ensure proper alignment. A touch of filing at...

Adjustable so you can run regular packs or shorty. The arrangement of the holes and notches allow 2mm incremental movement. ...A 2mm pin is required for the hinge, 2mm bolts and nuts hold the notched piece in place, and 2mm bolts to attache the tabs to...

Anyways I had to get a new pinion, but there aren't any 48p 5mm bore pinions, which meant I had to buy a different pitch pinion, which also means I had to buy a new spur gear to match, but there also isn't any traxxas spur gears for my car with...

Created a bracket to install two 40mm fans using the stock Traxxas Sledge motor mount.

3d print a replacement camber link for your Traxxas Rustler 2WD. May fit other models. I printed this one in neon green. ...0.2 layer height, 100% infill for a strong print.

Nice big floaty skis for 1/10 Traxxas 2wd. The skids are about 2" (50mm) x 6" (150mm) not counting the kick ups. Risers are sized for Slash tire size, Rustler and Bandit conversions will have the front sitting a bit higher than stock which is...

Used this design and the following .stl files to make a fat wheelie bar for the 1/10 2WD Traxxas...

Replacing the worn-out VXL chassis on my Traxxas Stampede 2WD means installing a durable new spindle, one that will take a pounding without sacrificing control. The original design often starts to wear down quickly due to constant use, making every...

Custom Front Wing and Rear Wing for Traxxas 2WD ONLY vehicles Provides adjustable downforce for speedruns! This is a pair of front and rear wings that have been designed to give adjustable amounts of downforce while producing very little drag. The...

Custom Front Wing and Rear Wing for Traxxas 2WD ONLY vehicles Provides adjustable downforce for speedruns! </h3> This is a pair of front and rear wings that have been designed to give adjustable amounts of downforce while producing very little...

I crafted a robust upgrade for my 2WD Stampede - a durable replacement bar made from high-quality TPU that's virtually indestructible. To maximize its performance, I suggest printing it in ABS or the premium choice of TPU or Polycarbonate, ensuring...

These are front and rear airless tires specifically designed for a Traxxas Stampede. I haven't had the chance to print and test these yet. They're intended to be printed with a low infill setting (under 25%) using TPU or any other flexible material.

Lifted esc mounts are designed specifically for two-wheel-drive Traxxas vehicles. They elevate the electronics securely by 7 millimeters. The dimensions of these mounts measure 6.65 inches wide and 1.69 inches long. ...For a secure installation, it's...

Soporte de batería para la Slash 2WD. ...Son dos versiones, diseñado para ser lo más parecido al original.

... on the thickness of your chosen fan (most are between 7-10mm thick). You can source these screws inexpensively on platforms like eBay or Aliexpress by searching for "30x30 5v fan." I opted to print this design in Pet-G for a strong snap fit.

Hey, built some skis for my Slash 2WD. Skis were printed with PLA and linkages with flexible filament, resulting in a smooth ride. The unique design allows for easy steering and maneuverability on various terrain types. ...Check out the video at...

I crafted those components using Nylon-Bridge and Nylon-910, ideal for withstanding intense impacts. For assembling the body, I recommend applying contact adhesive to achieve a flexible bond. ...Now it's time to get creative!

Fixing battery was always annoying for me, so I prepared an "easy-click" solution. This holder you need just to (1) rotate down holder plate and then (2) rotate clip arm pressing holder plate to the battery, like photos shows. Important is to fix...

Attaches to the rear shock tower with 2mm bolts and nuts, the part that holds the esc in attaches with 2mm bolts. ...Fusion 360 file included to make custom modifications easier.

Fixing battery was always annoying for me, so I prepared an "easy-click" solution. This holder you need just to (1) rotate down holder plate and then (2) rotate clip arm pressing holder plate to the battery, like photos shows. Important is to fix...

UPDATE: Version 3 Is Ready For The Field! This version 3 features several crucial adjustments that significantly improve its performance. The chassis hole position has been adjusted by a precise 0.5mm to ensure optimal clearance and minimize...

An 86-tooth pinion gear is ideal for use in both the 2WD and 4WD versions of Traxxas Slash vehicles, enhancing their performance with a high-quality upgrade.

The front section of the Traxxas Slash 2WD model awaits your attention, pending the first step in bringing it to life – printing it. Has anyone attempted this print? If so, please share the results. Print with 100% Infill Preparation Print...

Dual 7 cell baterry adapter for traxxas slash

Not compatible with Drag Slash as it has an updated Magnum 272R transmission.Print with supports for lifted tag only. Drill the holes for screws with thin sharp knife, reamer or 3mm drill bit.RUКрышка редуктора для старых 2wd моделей. Замена деталям...

I built this stand for my son's Traxxas Rustler 2wd 1:10 scale so he can store it safely with wheels off the ground. I left the front of the stand open to create some useful space under the car, and our model battery charger (Traxxas EZ Peak Plus)...

Simple esc mount and gnss for slash lcg 2wd chassis. If you found this, no explanation is needed. ...Enjoy!!