traxxas slash 2wd motor fan 3d models

Replacement front A arm for a Traxxas slash. All parameters have been tuned to properly fit, but if you want to change any, or if you want to modify the arm for use on another platform, the OpenSCAD file is included, and there is a diagram explaining...

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

Traxxas rear uprights. Stock look with a little more strength added in with rounds. I haven't printed this yet, just measured and drew it up. ... So it may need a few fixes in the future.

These short arms I designed specifically to accommodate a Lightning McQueen body on a Traxxas Nitro Rustler chassis are quite impressive. ...Stock Bandit rear arms were used in their construction.

I wanted to mount my old Slash body on the wall so I made this I have not printed this yet so it might not work

Battery Tie Down with a solid center section to allow the mounting of ESC and Receiver as far back on the slash chassis but keeping the weight centered.

... that would probably malfunction, I came up with this. This is a direct replacement for the stock motor end cap on the Velineon 3500 motor. ... Also check out my other designs for the Traxxas Rustler here: https://www.thingiverse.com/kbedrich/designs

These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. ...I have not attempted to print it yet, but the dimensions are the same.

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. ...Uses same holes in chassis as Traxxas original ESC. ... I made it 3mm thick, cut it in your slicer depending on how thick you want it.

for PL 1/10 slash raptor body(real scale) miror when you attach on your toy body, each side needs "dia 2mm, length 8mm, 3screws for each side, total 6 screws need)

I'm doing a slash speed run project without breaking the bank by opting for plastic alternatives instead of metal. They're not only affordable but also incredibly lightweight, making them perfect for printing with ease - the end result is...

For my Slash 4x4 ultimate, as a replacement for the original VXL 3S controller The adapter can take controllers up to a maximum width of 40mm Controllers are available here>>> https://amzn.to/33UHdMk Video: https://www.youtube.com/watch?v=74zSqdlPX2Y

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

A simple plate for mounting esc's to the slash. Uses stock mounting holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here...

I have not attempted to print it yet, but the dimensions are the same. Print instructionsCategory: Toys & Games Summary These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear...

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

Created this pinion with F360 to accomodate a cheap 3300Kv brushless motor I bought on Amazon. Printed out of PLA, I have only had one strip so far while driving WOT in deep-ish snow with the snow slingers on all 4 wheels. Might last longer out of...

Model of Traxxas 2.5R Nitro Motor. I have finished the outside appearance, however I am still in the process of refining the inside of the motor. ...I have the Piston, Crankshaft, and sleeve done, but I need to get the ports finished and the internal...

A holder for a 60mm cooler is designed to cool the engine of the Traxxas X-MAXX. This component is necessary for the motor's operation. Print Settings: Printer Brand is Ultimaker. The printer used is an Ultimaker 2. ...Infill percentage is set at 20%...

Engineer designs 2-wheel drive vehicle framework mount on both sides. ...A three-dimensional CAD file created using SolidWorks is provided as a digital source reference.

Ali express link: https://ae01.alicdn.com/kf/Hef260467673f44e5952652b5f3ca74df2/10PCS-Gdstime-5010-50-50-10-12V-cooling-fan-2PIN-50mm-5cm-Brushless-for-laptop-cooling.jpg_220x220xz.jpg it will need a voltage modulator to allow proper operation under...

Engine mount for 3.3, 2.0 and 1.5 _nitro engines_ ( i made it for a old T-maxx, traxxas says its the same part for all those engines, hadn't cheked) Should be compatible with: T-maxx TRX® 2.5R TRX® Pro .15 RX® 3.3 Basicaly all nitro engines.

It is a cover designed for Traxxas Slash 4x4 1/10 scale. Works pretty well, but is not suitable for bashing (it will break very probably because it is too stiff). Now you can drive in mud, stones, grass and nothing goes inside. It is also easier to...

It is a cover designed for Traxxas Slash 4x4 1/10 scale. Works pretty well, but is not suitable for bashing (it will break very probably because it is too stiff). Now you can drive in mud, stones, grass and nothing goes inside. It is also easier to...

ESC plate for LCG slash 2wd to mount max 10 esc and power button

This is a motor mount designed specifically for the Velineon VXL-3S system, featuring a durable 20mm fan to keep components cool and efficient.