traxxas slash 2wd esc mounting plate 3d models
562706 3d models found related to traxxas slash 2wd esc mounting plate.cults3d
3d print a plate thats used to mount your ESC to your RC car. Use 2 way tape to hold your ESC to the plate which is held on by 2 screws in the original location on the chassis. Plate is 3mm thick. Prints very easy with no supports. 0.3 layer height...
thingiverse
This is a straightforward flat ESC Mount designed to seamlessly fit into the stock ESC location on both the stock Traxxas Slash 2WD Chassis and the Low Center of Gravity (LCG) Chassis. It might also work with other models that utilize the XL-5 ESC,...
thingiverse
Attaches to the rear shock tower with 2mm bolts and nuts, the part that holds the esc in attaches with 2mm bolts. ...Fusion 360 file included to make custom modifications easier.
thingiverse
Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.
cults3d
Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.
thingiverse
The mounting holes allow it to be securely attached to the Traxxas Slash 2WD stock chassis as well as the 2WD LCG chassis. A convenient feature of this mount includes a spot where you can place the switch with narrow cutouts that tuck the wires...
thingiverse
A simple plate for mounting esc's to the slash. Uses stock mounting holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here...
thingiverse
Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. ...Uses same holes in chassis as Traxxas original ESC. ... I made it 3mm thick, cut it in your slicer depending on how thick you want it.
thingiverse
Lifted esc mounts are designed specifically for two-wheel-drive Traxxas vehicles. They elevate the electronics securely by 7 millimeters. The dimensions of these mounts measure 6.65 inches wide and 1.69 inches long. ...For a secure installation, it's...
thingiverse
Printed for a Traxxas Slash 2wd. The 4x4 setup is a distinct configuration. This one doesn't utilize bushings or bearings, which may cause it to wear out rapidly. However, it appears to hold up remarkably well nonetheless. ... Thanks for the...
thingiverse
I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.
thingiverse
... are unknown; testing is needed. Updated on March 9, 2018: Added universal mount plates for the Traxxas Slash 2WD. The plates include one clean design and another with ziptie/cable tie holes. ... Design another version if you provide the dimensions.
cults3d
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....
thingiverse
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...
thingiverse
Simple mounting plate to mount GNSS to the front of the Slash chassis right under the front shock tower. ...I use Velcro to mount the GNSS to the plate.
cults3d
esc mounting plate for the Traxxas Slash 2wd trucks with the LCG, low center of gravity chassis. This allows you to securely mount any esc that you would like using double sided tape or another attachment method of your choosing. ...This changes the esc...
thingiverse
Traxxas mount for larger Castle SW4 ESC. ... Adapts current ESC location to allow a clamshell style mount to hold up to bashing.
thingiverse
This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...
thingiverse
I'm upgrading the bandit's stock mounting plates since one of them broke, allowing users to choose any ESC they prefer by drilling their own screw holes. To accommodate future battery upgrades, I'll also create spacers. ...I haven't printed it yet, but...
thingiverse
Needed a sturdy platform to install a high-performance castle ESC on my rugged 4x4 Stampede truck. ...This solution fit perfectly, utilizing the vehicle's existing ESC mounting holes without any modifications required.
thingiverse
traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.
thingiverse
This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL as it spent far too much time on its roof! In addition to the printed parts you will need the following parts: 2x 625 bearings 2x M5x20 countersunk head bolts 2x BS210 O-rings 4x...
thingiverse
This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...
thingiverse
Just a flat plate for mounting just about any ESC into the HCG slash chassis, I was able to fit a GoolRC 3s ESC off Ebay onto it without any issues.
thingiverse
But, if you want more springiness and are going to use a winch, I would suggest using a 3 cm spring between the mount and plow. (If I find that it becomes a pain and keeps falling out, I can fabricate a shock for it). ... You will need: - 10 to 13...
thingiverse
Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.
thingiverse
For the Traxxas Slash 4X4 LCG Chassis: A means had to be found to secure the Castle Creations Mamba-X ESC to the Traxxas Slash 4X4 LCG and relocate the Receiver. I plan to use a chassis brace so relocation of the receiver to the front center of the...
thingiverse
Mount a Traxxas Slash 4x4 Esc Mounting Plate on Any Vehicle. ...Attach Double-Sided Tape Directly to the Esc, Secure it Firmly in Place on the Plate.
grabcad
Front Axle for Traxxas Slash 2WD Off-Road Short Course Truck.
cults3d
Adapter plate to mount any esc to a traxxas Slash 4x4. ...Use double side tape to glue the ESC to the plate.