traxxas slash 2wd body 3d models

Edit it online at https://www.tinkercad.com/things/4rkdmsXWDvF This is a fast-paced, makeshift version of a 30mm Battery Holder for the Traxxas Slash 4x4. (Had to be ready to race overnight, including printing...) It fits into the standard Battery...

I've designed a custom 3D printed switch mount for my Traxxas Slash 4x4 HCG, specifically to house the brushless motor system's switch. Since it needs to be installed somewhere, I'm providing this file with installation details. To download and...

These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear arms were used. Added V2 model. ...I have not attempted to print it yet, but the dimensions are the same.

Extend the Wheelbase of a Traxxas Bandit or Rustler to have the same wheelbase as the Slash. 46mm extension. This is great if you want to make a Drag car and don't want to change the entire chassis of your existing RC to the LCG Slash Chassis. This...

I designed these light pods to attach to a stock Traxxas Slash bumper. To install, drill a hole in the bumper and thread an M3 screw through the hole in the bracket and into the bumper. Then stick the LEDs into the other hole. I used some random 5mm...

The design is specifically tailored for the Traxxas Slash 1/16 model, but it can potentially be resized to fit a 1/10 scale model by applying a simple calculation: current size multiplied by 16, then divided by 10. I obtained the tire designs from...

This is a quick-build version of a 35mm battery holder for the Traxxas Slash 4x4. I had to get it ready to race overnight, including printing. Fits into standard battery holder holes/pins but replaces the bridge with a new one that hosts batteries...

I managed to lose the gear cover of my Traxxas Slash 4x4 LCG, which was a real bummer :(. So I came up with my own design. It's nearly as perfect as the original piece, but it has its own unique touches. After several test prints and model...

- Fits Traxxas Slash 1/16 Scale Model Cars Perfectly. - Should Be Easily Resizable to 1/10 Size by Multiplying the Current Size by 1.6. - Tires Were Remixed from https://www.thingiverse.com/thing:4326258 - There Are Three Versions of Tires Available:...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

traxxas chassis for rustler or bandit, made smaller so can fit on printer bed.

I have not attempted to print it yet, but the dimensions are the same. Print instructionsCategory: Toys & Games Summary These are very short arms I created to fit a Lightning McQueen body onto a Traxxas Nitro Rustler chassis. Stock Bandit rear...

Replacement front A arm for a Traxxas slash. All parameters have been tuned to properly fit, but if you want to change any, or if you want to modify the arm for use on another platform, the OpenSCAD file is included, and there is a diagram explaining...

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

Mounting plate for Traxxas VXL speed controller. ...bought truck in 2013 so not sure how this would mount on newer trucks.

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...

Traxxas rear uprights. Stock look with a little more strength added in with rounds. I haven't printed this yet, just measured and drew it up. ... So it may need a few fixes in the future.

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

Battery Tie Down with a solid center section to allow the mounting of ESC and Receiver as far back on the slash chassis but keeping the weight centered.

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

This is replacement for oryginal Traxxas part number 6893. I recommend to use it as a temoprary solution, it is always better to have a rigid original part. But if you need this part now and you must wait some days for the delivery, this is a working...

Simple print to get a flat surface for the ESC in TRX-7422 LCG chassis. ...Uses same holes in chassis as Traxxas original ESC. ... I made it 3mm thick, cut it in your slicer depending on how thick you want it.

A simple plate for mounting esc's to the slash. Uses stock mounting holes and stock screws, the heads are countersunk for a flat mounting surface. Use double-sided tape to stick the esc down, it works extremely well. ... Install video here...

I'm doing a slash speed run project without breaking the bank by opting for plastic alternatives instead of metal. They're not only affordable but also incredibly lightweight, making them perfect for printing with ease - the end result is...

For my Slash 4x4 ultimate, as a replacement for the original VXL 3S controller The adapter can take controllers up to a maximum width of 40mm Controllers are available here>>> https://amzn.to/33UHdMk Video: https://www.youtube.com/watch?v=74zSqdlPX2Y

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

you can use this for lift your body. ... Print 100% infill, 0,2mm layerheight

you can use this for lift your body. ... Print 100% infill, 0,2mm layerheight

longer body post for the 1/16 traxxas slash / e revo

The bearings are available from traxxas or here cheaper: http://www.kingheads.com/product_info.php?products_id=934 UPDATE 05/05/15: I've updated the design to allow for two motors with a reverse mount on one side. UPDATE 06/16/15: A friend of mine...